Kubota K008-5 страница 124 Скачать руководство пользователя

Страница: 124 / 168

122

W9215-8135-1

06/2021

Troubleshooting

Troubleshooting: Buzzer sounds

No. Item

Possible
cause

Sounds

Problem / Mal-
function

Preliminary measure Solution

1. Anti-theft

Wrong key, un-
able to start.

PiPiPi

The machine can-
not be started be-
cause the wrong
key has been in-
serted.

Use the correct key.

–

2. Anti-theft

Red registra-
tion key, una-
ble to start.

PiPiPi

Try starting the
engine with the
red key (for regis-
tration).

Use the correct key.

–

Control lever
lock

Lower the con-
trol lever lock
to start the en-
gine.

PiPiPi

The machine can-
not be started with
lowering the con-
trol lever lock.

Raise the control le-
ver lock.

–

4. Anti-theft

Forgot to re-
move the key.

PiPiPi

Key must be
pulled out.

Pull out the key.

–

Control lever
lock

Control lever
lock solenoid
shorts.

PiPiPiPiPiPi ...
(Continuous
sounds)

There is a failure
in the control lever
lock.

Engine may be start-
ed but the machine
cannot move.

Inform your
KUBOTA dealer
immediately.

Power sup-
ply

Overvoltage

PiPiPiPiPiPi ...
(Continuous
sounds)

–

The engine was
started by connect-
ing a booster cable
from a 24V battery
or machine. Or the
alternator is out of
order.

Please stop
starting the en-
gine in the 24 V
system immedi-
ately.

7. Anti-theft

Antenna ab-
normality

PiPiPiPiPiPi ...
(Continuous
sounds)

The anti-theft sys-
tem has failed.
The engine can-
not start.

–

Inform your
KUBOTA dealer
immediately.

Power sup-
ply

External 12V
short

PiPiPiPiPiPi ...
(Continuous
sounds)

–

9. Seat belt

Engine starts
and the seat
belt is not
latched inside
the buckle.

PiPiPi ... PiPiPi
(Every 2 sec-
onds continu-
ous sounds)

Seat belt must be
latched inside the
buckle.

Securely insert the
seat belt inside the
buckle.

–

Содержание K008-5









































































































































































Результаты поиска

Содержание K008-5

Отзывы:

Похожие инструкции для K008-5

Бренды по названию

Популярные бренды

Kubota K008-5, Руководство по эксплуатации

Результаты поиска

Содержание K008-5

Отзывы:

Похожие инструкции для K008-5

Бренды по названию

Популярные бренды