manualshive.com logo in svg

Kubota K008-5, Руководство по эксплуатации

Поделиться
Скачать
Kubota K008-5 Скачать руководство пользователя страница 115

Operation

W9215-8135-1

113

06/2021

Replacing the bucket

Anti-theft system

The excavator is equipped with an anti-theft system that restricts the engine to only being started using a regis-
tered key. If a registered key gets lost or stolen, you can invalidate it. This will prevent the engine from being started
with this key, thus protecting the vehicle against theft. The anti-theft system makes it difficult to steal the machine.
However, it cannot prevent theft completely.

If the starter switch is set to STOP, the indicator light (1) is illuminat-
ed, indicating the activation of the anti-theft system.

Make  sure  that  the  indicator  light  is  illuminated  when  leaving  the
machine.

When replacing the bucket, make sure to wear eye protection, a helmet and protective gloves.

During attaching and detaching, chippings and burrs may appear on the bolts or bushings. These
may cause severe injuries.

Never use your fingers for the alignment of the components (linkage, bucket, arm). The components
may sever your fingers by uncontrolled movements.

STOP

STOP

STOP

Содержание K008-5









































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды