KTM 690 DUKE R AUS/UK Скачать руководство пользователя

Страница: 118 / 187

ELECTRICAL SYSTEM

116

–

Remove the headlight mask with the headlight. (

p. 107)

700175-01

–

Set down the headlight mask in front of you as shown in the illustration and carefully
tilt the high beam headlight in the direction of the low beam headlight.

–

Turn the bulb holder



about 30° counterclockwise and remove it.

700176-01

–

Pull the parking light bulb out of the holder.

–

Insert a new parking light bulb in the holder.

Parking light (W5W / socket W2.1x9.5d) (

p. 162)

–

Position the bulb holder and turn it clockwise as far as it will go.

–

Install the headlight mask with the headlight. (

p. 109)

13.11

Changing the turn signal bulb

Note

Damage to reflector

Reduced luminance.

–

Grease on the lamp will evaporate due to the heat and be deposited on the reflector. Clean the lamp and keep it free of grease before
mounting.

Содержание 690 DUKE R AUS/UK




























































































































































































Результаты поиска

Содержание 690 DUKE R AUS/UK

Отзывы:

Похожие инструкции для 690 DUKE R AUS/UK

Бренды по названию

Популярные бренды

KTM 690 DUKE R AUS/UK, Руководство пользователя

Результаты поиска

Содержание 690 DUKE R AUS/UK

Отзывы:

Похожие инструкции для 690 DUKE R AUS/UK

Бренды по названию

Популярные бренды