manualshive.com logo in svg

KTM 690 DUKE R AUS/UK, Руководство пользователя, Страница: 75 / 187

Поделиться
Скачать
KTM 690 DUKE R AUS/UK Скачать руководство пользователя страница 75

SERVICE WORK ON THE CHASSIS

73

100131-10

–

Loosen nut

.

–

Loosen nuts

.

–

Adjust the chain tension by turning adjusting screws

on the left and right.

Guideline

Chain tension

5 mm (0.2 in)

Turn the left and right adjusting screws

so that the markings on the left and right

chain adjusters

are in the same position relative to the reference marks

. The

rear wheel is then correctly aligned.

Info

The upper chain section must be taut.
Chain wear is not always even, so you should check this setting at different
chain positions.

–

Tighten nuts

.

–

Make sure that the chain adjusters

are installed correctly on adjusting screws

.

–

Tighten nut

.

Guideline

Nut, rear wheel spindle

M25x1.5

90 Nm
(66.4 lbf ft)

Info

The wide adjustment range of the chain adjusters (30 mm (1.18 in)) enables
different secondary transmissions with the same chain length.
The chain adjusters

can be turned through 180°.

Содержание 690 DUKE R AUS/UK




























































































































































































Отзывы:

Нет отзывов