KTM 690 DUKE R AUS/UK Скачать руководство пользователя

Страница: 130 / 187

COOLING SYSTEM

128

Condition

Fuel tank is reset or removed.

700182-10

–

Remove radiator cap



700183-01

–

Remove bleeder screw



–

Tilt the vehicle slightly to the right.

–

Pour in coolant until it emerges without bubbles at the vent hole, and then mount and
tighten the bleeder screw immediately.

Alternative 1

Coolant (

p. 173)

Alternative 2

Coolant (mixed ready to use) (

p. 173)

–

Fill the radiator completely with coolant. Mount the radiator cap.

–

Rest the vehicle on the sidestand.

Fuel tank is reset.

–

Move the fuel tank forward.

The fuel tank is removed.

–

Connect and position the fuel tank.

Содержание 690 DUKE R AUS/UK




























































































































































































Результаты поиска

Содержание 690 DUKE R AUS/UK

Отзывы:

Похожие инструкции для 690 DUKE R AUS/UK

Бренды по названию

Популярные бренды

KTM 690 DUKE R AUS/UK, Руководство пользователя

Результаты поиска

Содержание 690 DUKE R AUS/UK

Отзывы:

Похожие инструкции для 690 DUKE R AUS/UK

Бренды по названию

Популярные бренды