KTM 690 DUKE R AUS/UK Скачать руководство пользователя

Страница: 77 / 187

SERVICE WORK ON THE CHASSIS

700152-01

–

Shift into neutral; pull the lower chain section with the specified weight



Guideline

Weight of chain wear measurement

15 kg (33 lb.)

–

Measure the distance



of 18 chain links in the lower chain section.

Info

Chain wear is not always even, so you should repeat this measurement at differ-
ent chain positions.

Maximum distance



at the longest

chain section

272 mm (10.71 in)

» If the distance



is greater than the specified measurement:

–

Replace the chain.

Info

When the chain is replaced, the rear sprocket and engine sprocket
should also be changed.
New chains wear out faster on old, worn sprockets.
For safety reasons, the chain has no chain joint.

302113-10

–

Check the chain sliding guard for wear.
» If the chain sliding guard is worn:

–

Replace the chain sliding guard.

–

Check that the chain sliding guard is firmly seated.
» If the chain sliding guard is loose:

–

Tighten the chain sliding guard.

Содержание 690 DUKE R AUS/UK




























































































































































































Результаты поиска

Содержание 690 DUKE R AUS/UK

Отзывы:

Похожие инструкции для 690 DUKE R AUS/UK

Бренды по названию

Популярные бренды

KTM 690 DUKE R AUS/UK, Руководство пользователя

Результаты поиска

Содержание 690 DUKE R AUS/UK

Отзывы:

Похожие инструкции для 690 DUKE R AUS/UK

Бренды по названию

Популярные бренды