KTM 125 EXC EU 2010 Скачать руководство пользователя | Manualshive

Страница: 57 / 140

background image

MAINTENANCE WORK ON CHASSIS AND ENGINE

55

400725-01

–

Clean the chain regularly and then treat with chain spray.

Chain cleaner (

p. 132)

Off-road chain spray (

p. 132)

11.41

Checking the chain tension

Warning

Danger of accidents

Danger caused by incorrect chain tension.

–

If the chain tension is too high, the components of the secondary power train (chain, engine sprocket, rear sprocket, bear-
ings in transmission and rear wheel) are under additional load. Apart from premature wear, in extreme cases the chain can
rupture or the countershaft of the transmission can break. On the other hand, if the chain is loose, it can fall off the engine
sprocket or the rear sprocket and block the rear wheel or damage the engine. Check the chain tension and correct if neces-
sary.

–

Jack up the motorcycle. (

p. 38)

400213-10

–

Push the chain at the end of the chain sliding component upwards to measure
chain tension



.

Info

The upper chain section



must be taut.

Chain wear is not always even, so you should repeat this measurement at
different chain positions.

Chain tension

8… 10 mm (0.31… 0.39 in)

» If the chain tension does not meet specifications:

–

Adjust the chain tension. (

p. 56)

–

Remove the motorcycle from the work stand. (

p. 38)

11.42

Checking the rear sprocket/engine sprocket for wear

400227-01

–

Check the rear sprocket/engine sprocket for wear.
» If the rear sprocket/engine sprocket are worn:

–

Replace the rear sprocket/engine sprocket.

Info

When fitting the chain joint, always make sure that the closed side
of the joint faces forward (riding direction).
The engine sprocket, rear sprocket and chain should always be
replaced together.

–

Check the chain guide for tightness and wear.

11.43

Checking chain wear

–

Jack up the motorcycle. (

p. 38)

«
...
55
56
57
58
59
...
»

Содержание 125 EXC EU 2010













































































































































Отзывы:

Нет отзывов

Похожие инструкции для 125 EXC EU 2010

Бренд: ICON Страницы: 2

Power commander GSXR750

Бренд: Dynojet Страницы: 4

Бренд: GAS GAS Страницы: 57

ST400 Cruiser Edition

Бренд: STEEL HORSE AUDIO Страницы: 6

Бренд: GAS GAS Страницы: 119

Бренд: KTM Страницы: 38

Бренд: hepco & becker Страницы: 7

Бренд: SHERCO Страницы: 102

Бренд: Bajaj Страницы: 39

Бренд: PIAGGIO Страницы: 8

Бренд: hepco & becker Страницы: 4

Бренд: hepco & becker Страницы: 2

Бренд: hepco & becker Страницы: 3

Бренд: bimota Страницы: 95

Бренд: Tractel Страницы: 12

Spyder ST Limited SE5

Бренд: Can-Am Страницы: 41

Бренд: hepco & becker Страницы: 2

Бренд: KTM Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды