KTM 125 EXC EU 2010 Скачать руководство пользователя | Manualshive

Страница: 79 / 140

background image

MAINTENANCE WORK ON CHASSIS AND ENGINE

77

B00044-10

(All 250/300 models)

Water pump



in the engine circulates the coolant.

The pressure resulting from the warming of the cooling system is regulated by a
valve in radiator cap



. This ensures that operating the vehicle at the specified

coolant temperature will not result in a risk of malfunctions.

120 °C (248 °F)

Cooling is effected by the air stream.
The lower the speed, the less the cooling effect. Dirty cooling fins also reduce the
cooling effect.

11.83

Checking the antifreeze and coolant level

Warning

Danger of scalding

During motorcycle operation, the coolant gets very hot and is under pressure.

–

Do not remove the radiator cap, radiator hoses or other cooling system components when the engine is hot. Allow the
engine and cooling system to cool down. In case of scalding, rinse immediately with lukewarm water.

Warning

Danger of poisoning

Coolant is poisonous and a health hazard.

–

Avoid contact between coolant and skin, eyes and clothing. If it gets into your eyes, rinse immediately with water and con-
tact a doctor. Wash affected skin areas immediately with soap and water. If coolant is swallowed, contact a doctor immedi-
ately. Change clothes that have come into contact with coolants. Keep coolant out of the reach of children.

Condition

The engine is cold.

400243-10

–

Stand the motorcycle upright on a horizontal surface.

–

Remove the radiator cap.

–

Check the coolant antifreeze.

−

25…

−

45 °C (

−

13…

−

49 °F)

» If the coolant antifreeze does not meet specifications:

–

Correct the coolant antifreeze.

–

Check the coolant level in the radiator.

Coolant level



above the radiator fins. 10 mm (0.39 in)

» If the level of the coolant does not meet specifications:

–

Correct the coolant level.

Alternative 1

Coolant (

p. 130)

Alternative 2

Coolant (mixed ready to use) (

p. 130)

–

Mount the radiator cap.

11.84

Checking the coolant level

Warning

Danger of scalding

During motorcycle operation, the coolant gets very hot and is under pressure.

–

Do not remove the radiator cap, radiator hoses or other cooling system components when the engine is hot. Allow the
engine and cooling system to cool down. In case of scalding, rinse immediately with lukewarm water.

Warning

Danger of poisoning

Coolant is poisonous and a health hazard.

–

Avoid contact between coolant and skin, eyes and clothing. If it gets into your eyes, rinse immediately with water and con-
tact a doctor. Wash affected skin areas immediately with soap and water. If coolant is swallowed, contact a doctor immedi-
ately. Change clothes that have come into contact with coolants. Keep coolant out of the reach of children.

Condition

The engine is cold.

«
...
77
78
79
80
81
...
»

Содержание 125 EXC EU 2010













































































































































Отзывы:

Нет отзывов

Похожие инструкции для 125 EXC EU 2010

Daytona Moto2 765 2020

Бренд: Triumph Страницы: 163

Бренд: X-lite Страницы: 84

Бренд: LAZER Страницы: 11

Бренд: AMFD Страницы: 17

Бренд: Clas Ohlson Страницы: 5

HPS.08.473.10000/B

Бренд: SW-Motech Страницы: 4

Бренд: Fantic Motor Страницы: 60

Бренд: MRA Страницы: 6

Бренд: Yamaha Страницы: 96

Бренд: Yamaha Страницы: 110

Tenere 700 2021

Бренд: Yamaha Страницы: 112

Tenere 700 2023

Бренд: Yamaha Страницы: 114

Super Tenere ES 2023

Бренд: Yamaha Страницы: 132

Tenere 700 2020

Бренд: Yamaha Страницы: 472

Бренд: Yamaha Страницы: 94

Бренд: Custom Dynamics Страницы: 2

Бренд: Royal Enfield Страницы: 234

Бренд: hepco & becker Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды