KTM 125 EXC EU 2010 Скачать руководство пользователя

Страница: 94 / 140

TROUBLESHOOTING

Faults

Possible cause

Action

Engine stalls or is popping into the
carburetor

Lack of fuel

–

Turn handle



of the fuel tap to the

posi-

tion.

–

Refuel. (

p. 33)

Engine takes in bad air

–

Check the intake flange and carburetor for
tightness.

Socket connector or ignition coil is
loose or oxidized

–

Clean the plug-in connector and treat it with
contact spray.

Engine overheats

Too little coolant in cooling system

–

Check the cooling system for leakage.

–

Check the coolant level. (

p. 77)

Too little air stream

–

Switch off engine when stationary.

Radiator fins very dirty

–

Clean the radiator fins.

Foam formation in cooling system

–

Drain the coolant.

(

p. 78)

–

Refill with coolant.

(

p. 79)

Damaged cylinder head or cylinder
head gasket

–

Check the cylinder head or cylinder head gas-
ket.

Bent radiator hose

–

Change the radiator hose.

Incorrect ignition point due to loose
stator

–

Adjust the ignition.

White smoke emission (steam in
exhaust gas)

Damaged cylinder head or cylinder
head gasket

–

Check the cylinder head or cylinder head gas-
ket.

Gear oil exits at the vent hose

Too much gear oil added

–

Check the gear oil level. (

p. 88)

Water in the gear oil

Damaged shaft seal ring or water
pump

–

Check the shaft seal ring and water pump.

Содержание 125 EXC EU 2010













































































































































Результаты поиска

Содержание 125 EXC EU 2010

Отзывы:

Похожие инструкции для 125 EXC EU 2010

Бренды по названию

Популярные бренды

KTM 125 EXC EU 2010, Руководство пользователя

Результаты поиска

Содержание 125 EXC EU 2010

Отзывы:

Похожие инструкции для 125 EXC EU 2010

Бренды по названию

Популярные бренды