background image

1-4 Operation 

  Do not disconnect the mains cable on the UPS system or the building wiring outlet 

(shockproof socket outlet) during operations since this would cancel the protective 
earthing of the UPS system and of all connected loads.   

  The UPS system features its own, internal current source (batteries). The UPS output 

sockets or output terminals block may be electrically live even if the UPS system is 
not connected to the building wiring outlet.   

  In order to fully disconnect the UPS system, first press the OFF/Enter button to 

disconnect the mains.   

  Prevent no fluids or other foreign objects from inside of the UPS system.   

1-5 Maintenance, service and faults 

  The UPS system operates with hazardous voltages. Repairs may be carried out only 

by qualified maintenance personnel.   

 

Caution

 - risk of electric shock. Even after the unit is disconnected from the mains 

(building wiring outlet), components inside the UPS system are still connected to the 
battery and electrically live and dangerous.   

  Before carrying out any kind of service and/or maintenance, disconnect the batteries 

and verify that no current is present and no hazardous voltage exists in the terminals 
of high capability capacitor such as BUS-capacitors.   

 Only persons are adequately familiar with batteries and with the required 

precautionary measures may replace batteries and supervise operations. 
Unauthorized persons must be kept well away from the batteries.   

 

Caution

 - risk of electric shock. The battery circuit is not isolated from the input 

voltage. Hazardous voltages may occur between the battery terminals and the 
ground. Before touching, please verify that no voltage is present!   

  Batteries may cause electric shock and have a high short-circuit current. Please take 

the precautionary measures specified below and any other measures necessary 
when working with batteries:   

remove wristwatches, rings and other metal objects   

use only tools with insulated grips and handles.   

  When changing batteries, install the same number and same type of batteries.   

  Do not attempt to dispose of batteries by burning them. This could cause battery 

explosion.  

  Do not open or destroy batteries. Escaping electrolyte can cause injury to the skin 

and eyes. It may be toxic.   

  Please replace the fuse only with the same type and amperage in order to avoid fire 

hazards.  

  Do not dismantle the UPS system.   

1-6 Symbols used in this guide 

 WARNING!

 

Risk of electric shock

 

CAUTION!

 

Read this information to avoid equipment damage 

Содержание UDC9101RTH






















Отзывы: