KSB 88980/02 Скачать руководство пользователя страница 28

Страница: 28 / 76

5.3.1.7 Installing the pump set

NOTE

For pumping water containing sludge and suspended solids pump sets with impeller type

S (cutter) are preferable. In such cases it is recommended to use an inclined claw.

NOTE

Make sure the pump set with the pre-assembled claw can easily be slipped over the

mounting bracket, threaded onto the guide rails and lowered down. If required, alter the

position of the crane during installation.

1. Guide the pump set over the suspension bracket/mounting bracket, thread it

onto the guide wires/rails and slowly lower it down.
The pump set attaches itself to duckfoot bend 72-1.

2. Attach the lifting chain/rope to hook 59-18 at the mounting bracket.

5.3.2 Transportable wet installation
Before installing the pump set, fit the 3 pump feet and foot plate, if applicable.

Fitting the pump feet

1. Undo screws 914.03.
2. Push pump feet 182 into the opening in the suction cover.
3. Tighten screws 914.03 again to the indicated tightening torque. (

⇨

Section 7.6

Page 48)

Fitting the foot plate

1. Fit the foot plate to the three pump feet with screws, discs and nuts. Observe the

tightening torques. (

⇨

Section 7.6 Page 48)

Attaching the lifting chain/rope

1. Attach the lifting chain or rope to the shackle on the discharge nozzle side (see

drawing and table "Types of attachment").

Connecting the piping

The DIN connection can be connected to rigid or flexible pipes.

Fig. 17: Connection options

UG1274785

Fig. 16: Attaching the
lifting chain/rope

5 Installation at Site

26 of 66

Amarex® N

Goodnal STP ST041 Biological Treatment (KSB WAS PUMP 1 & 2 PU-0530-010 OM Instructions) Vendor Manual

Q-Pulse Id VM381

Active 29/10/2013

Page 28 of 76

Содержание 88980/02













































































Результаты поиска

Содержание 88980/02

Отзывы:

Похожие инструкции для 88980/02

Бренды по названию

Популярные бренды

KSB 88980/02, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание 88980/02

Отзывы:

Похожие инструкции для 88980/02

Бренды по названию

Популярные бренды