KSB 88980/02 Скачать руководство пользователя страница 48

Страница: 48 / 76

CAUTION

Incorrect installation

Clearance gap inaccurate!

▷

Pull the rotor assembly right up to the suction cover until it will not go any
further. Maintain this position until dimensions x and y have been measured.

Fig. 26: Pulling the rotor assembly right up to the suction cover
6. Pull the rotor assembly right up to the suction cover until it will not go any

further.

2563:114

Fig. 27: Adjusting impeller type S

Distance between suction cover and pump casing

Clearance gap between suction cover and impeller vanes

Distance between the upper side of the suction cover and the mounting holes
of the suction cover

Distance between the bottom of the pump casing and the impeller vanes

7. Measure dimension x on the suction cover

Dimension x is the distance between the upper side of the suction cover and the
mounting holes of the suction cover.

8. Measure dimension y between pump casing and impeller vanes.

Dimension y is the distance between the bottom of the pump casing and the
impeller vanes.

9. Use screws 904 to set dimension h (h = x + s - y),

where s (0.3 + -0.1) is the clearance between the suction cover and the impeller
vanes.

10. Tighten the suction cover with screws 914.03.
11. Rotate the impeller body to check that the impeller turns smoothly.

Make sure that the suction cover and impeller do not touch each other.

7.5.2.2.2 Fitting impeller type D

NOTE

For bearing brackets with tapered fit make sure that the tapered fit of impeller and shaft

is undamaged and installed free from grease.

7 Servicing/Maintenance

46 of 66

Amarex® N

Goodnal STP ST041 Biological Treatment (KSB WAS PUMP 1 & 2 PU-0530-010 OM Instructions) Vendor Manual

Q-Pulse Id VM381

Active 29/10/2013

Page 48 of 76

Содержание 88980/02













































































Результаты поиска

Содержание 88980/02

Отзывы:

Похожие инструкции для 88980/02

Бренды по названию

Популярные бренды

KSB 88980/02, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание 88980/02

Отзывы:

Похожие инструкции для 88980/02

Бренды по названию

Популярные бренды