Krone EasyCut F 280 Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 96

Krone EasyCut F 280 Скачать руководство пользователя страница 65

Maintenance

65

•  Remove the cutting disc or drum.
•  Remove retaining ring (7).
•  Unscrew the hexagon head bolts (8).
•  Use the special key (10) included with delivery to remove the nut (2).
•  Remove the hub (1).
•  Remove the damaged shear pins (3).
•  Check the nut and hub for damage. Replace damaged parts with KRONE original

replacement parts.

•  Fill the space above the bearing with grease (c).
•  Place the hub on the pinion shaft.
•  Drive the new shear pins (3) through the hub (1) and shaft (4).

Note - Note the position of the shear pins!

• Drive the shear pins (3) into the hole from outside until the end of the pin reaches the

surface of the hub (d).

• he slots of the shear pins (3) must be mounted facing each other horizontally (see detail (I)).

• Install the nut (2) using the special key (10) included with delivery (tighten to a tightening

torque of 300 Nm).

•  Install and tighten the hexagon head bolts (8) with detent edged washers.
•  Install the retaining ring (7).
•  Install the cutting disc (5) or blade drum (6).

Pos: 106 /BA/Einstellungen/M ähwer ke/Einstell ung der Keilriemenspannung EC F 280 / F 320 @ 104 \mod_1332324556266_78.docx @ 942981 @ 2 @ 1

11.6

Setting of the V-belt Tension
(except EasyCut F 280 M / EasyCut F 320 M / EasyCut F 360 M)

Fig. 33
The drive V-belts maintain their tension by means of a compression spring (2). To adjust

dimension "a", unscrew the nut (1). Turn the nuts until dimension "a" = 205 mm is reached. Lock

nuts again.

Pos: 107 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

«
...
63
64
65
66
67
...
»

Содержание EasyCut F 280

































































































Отзывы:

Нет отзывов