Krone EasyCut F 280 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 96

Krone EasyCut F 280 Скачать руководство пользователя страница 42

Start-up

42

Pos: 94.28 /Ü berschriften/Ü berschriften 2/A-E/AAnbau und Ei nstellung der Entlastungsfedern ÜS @ 89\mod_1321958243040_78.docx @ 756797 @ 2 @ 1

7.6

Mounting and Adjusting the Relief Springs

Pos: 94.29 /BA/Sicherheit/7. Gefahr enhinweise alt/M ähwer ke/Gefahr - Ei nstellung an den Entl astungsfeder n @ 0\mod_1196751594562_78.docx @ 12575 @ @ 1

Danger! - Setting on the compensation springs

Effect: Danger to life or serious injuries
• The compensation springs must only be removed in transport position. In the working

position the compensation springs are subject to high tensile stress.

• Severe injury can be caused if the compensation springs are removed while in the working

position.

• The lower threaded blocks on the compensation springs must be fully screwed in.

Pos: 94.30 /BA/Ei nstellungen/M ähwer ke/EasyCut/Entl astungsfeder(n)/Entl astungsfedern am Tr aktor einstell en Bild EC F 280/320/3 60 @ 136\mod_1352878872691_78.docx @ 1211577 @ @ 1

Fig. 19

Pos: 94.31 /BA/Ei nstellungen/M ähwer ke/EasyCut/Entl astungsfeder(n)/Entl astungsfedern am Tr aktor einstell en Text EC 28/32 28/32 C V @ 10\mod_1221737190442_78.docx @ 136798 @ @ 1

•  Bring the front mowing unit into the transport position
•  Hook compensation spring (3) onto perforated bar (4).
•  Attach with holder (2) on support point

"a"

and secure with hinged cotter pin (1)

Pos: 94.32 /BA/Ei nstellungen/M ähwer ke/EasyCut/Entl astungsfeder(n)/Ei nstellen der Entl astungsfeder n am Tr aktor Maß 300-400 Hinweis @ 10\mod_1221737438036_78.docx @ 136841 @ @ 1

Note

Setting dimension of the compensation springs
Effect: Proper use of the machine.

The distance between support point "a" of the compensation spring (3) and the pivot point of

the tractor's lower suspension arms (5) should be between 300 – 400 mm.

Pos: 94.33 /BA/Inbetri ebnahme/EasyCut/Probel auf nach Erstmontag e @ 3\mod_1205215927275_78.docx @ 73555 @ 2 @ 1

7.7

Trial run after first installation

Caution!

After the first connection to the tractor, the machine must undergo a trial run.
• The machine must be in working position
• Do not switch on the PTO until the machine is resting on the ground and you are absolutely

sure that there are no persons, animals or objects in the danger zone.

• Start a trial run of the machine from the driver’s seat of the tractor only.

•  Lower the machine into working position.
•  Carefully switch in the PTO of the tractor.
•  Slowly increase the PTO speed to 1000 rpm.
•  Check that the machine is running smoothly and without vibrations.
•  Reduce the PTO speed to idling and wait for the cutting discs / mower drums to come to a

stansdstill.

• Raise or lower the machine via the tractor hydraulics.

Pos: 94.34 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

«
...
40
41
42
43
44
...
»

Содержание EasyCut F 280

































































































Отзывы:

Нет отзывов