manualshive.com logo in svg

Krone BiG X 1000, Оригинальная инструкция по эксплуатации, Страница: 26 / 120

Поделиться
Скачать
Krone BiG X 1000 Скачать руководство пользователя страница 26

II - 4

Safety

13. Caution! After switching off the PTO, there is

danger due to the inertia of the flywheel mass!
Keep away from the implement during this time. Be
sure that the machine has come to a complete
stop before starting any maintenance work.

14. Cleaning, lubricating or adjusting PTO driven

implements or the PTO shaft only with PTO
disengaged, engine switched off and ignition key
withdrawn!

15. Place the uncoupled PTO shaft on the holder

provided!

16. After detaching the PTO shaft, fit the protective

sleeve on the PTO stump!

17. Immediately repair any damage before working with

the implement!

2.2.9 Hydraulic system

1. The hydraulic system is pressurised!

2. When connecting hydraulic cylinders and motors,

make sure the hydraulic hoses are connected as
specified!

3. When connecting the hydraulic hoses to the forage

harvester hydraulics, take care that the hydraulic
system is depressurised both on the tractor side
and on the device side!

4. When functions are connected hydraulically between

the forage harvester and the front attachment,
coupling sleeves and plugs should be identified so
that faulty operation is excluded! If the connectors
are interchanged, the functions will be reversed (e.g.
raising/lowering) - Risk of accident!

5. Check the hydraulic hose lines at regular intervals

and replace them if damaged or worn! The
replacement hose lines must meet the technical
requirements of the device manufacturer!

6. When searching for leaks, use suitable aids to

avoid the risk of injuries!

7. Liquids escaping under high pressure (hydraulic oil)

can penetrate the skin and cause serious injury! In
the case of injuries, seek medical assistance
immediately. Risk of infection!

8. Before working on the hydraulic system,

depressurise the system and switch off the engine!

2.2.7 Implements

1. Caution! Once the drives have been switched off,

a hazard remains from the flywheel which
continues to turn by inertia! Keep away from the
implement during this time. Be sure that the
machine has come to a complete stop before
starting any maintenance work!

2. Cleaning, lubricating and adjusting the implements

must be carried out only when the drive is switched
off, the engine switched off and the ignition key
removed!

2.2.8 PTO operation

1. Only PTO shafts specified by the manufacturer

may be used!

2. The protective tube and protective funnel of the

PTO shaft as well as the PTO shield - also on the
implement end - must be attached and in proper
condition!

3. Make sure that the required tube covers for PTO

shafts are in place in transport and working
position!

4. Before installing or detaching PTO shafts, switch

off the PTO shaft, turn the engine off and remove
the ignition key!

5. When using PTO shafts with an overload or free-

wheel coupling that is not covered by the protective
equipment on the tractor, the overload or free-wheel
couplings must be attached to the device!

6. Always make sure that the PTO shafts are

mounted correctly and secured properly!

7. Secure the PTO shaft guard against turning by

hooking in the chains!

8. Before switching on the PTO shaft, make sure that

the selected PTO shaft speed of the tractor agrees
with the permissible speed of the device!

9. Before switching on the PTO shaft make sure that

no person is in the hazard area of the device!

10. Never switch on the PTO with the engine switched

off!

11. While working with the PTO, nobody is permitted to

stay in the range of the turning PTO or PTO shaft.

12. Always switch off the PTO in the case of

excessive bending and if the PTO is not required!

https://tractormanualz.com

Содержание BiG X 1000

























































































































Отзывы:

Нет отзывов