manualshive.com logo in svg

Krone AM 203 CV, Руководство по эксплуатации

Поделиться
Скачать
Krone AM 203 CV Скачать руководство пользователя страница 4

2

List of Contents

I.

Foreword .............................................................................................................................. 1

II.

List of Contents ..................................................................................................................... 2

III.

General .................................................................................................................................. 3

1.

Introduction

1.1

Position of Information Labels with safety-relevant contents on the Machine ....................... 6

1.2

Position of General Information Labels on the Machine ....................................................... 8

1.3

Technical Data for Disc Mower ............................................................................................. 9

2.

Preparing for Operation

2.1

Attaching the Disc Mower to the Tractor ............................................................................. 10

2.2

P.T.O. Shaft ......................................................................................................................... 12

2.3

Jack Stand ........................................................................................................................... 13

2.4

Conditioner Drive (lever change gearbox) .......................................................................... 13

2.5

The angle of the mower to the tractor ................................................................................. 14

2.6

Preparing to turn ................................................................................................................. 14

2.7

Transport Position ............................................................................................................... 15

2.8

Detaching the Disc Mower to the Tractor ............................................................................ 16

3.

Adjusting the Disc Mower

3.1

Adjusting the Top Link Arm Coupling Point ........................................................................ 18

3.2

Adjusting the Safety Breakaway unit .................................................................................. 18

3.3

Adjusting the Compensating Spring for the Cutter Beam ................................................... 19

3.4

Adjusting piece for lifting cylinder and flotation spring ........................................................ 19

3.5

Basic Setting for the Tractor Lower Link Arm ..................................................................... 19

3.6

Adjusting the Swath Width .................................................................................................. 20

3.7

Adjusting the cutting height ................................................................................................. 20

3.8

Changing Blades on the Cutting Discs with Blade Screw Connectors ............................... 21

3.9

Adjusting the Conditioner Speed ........................................................................................ 22

3.10

Adjusting the Conditioner Cover Plate ................................................................................ 22

3.11

Adjusting the Position of the Condtioner rotor to the Cutterbar .......................................... 23

4.

Maintenance

4.1

General ................................................................................................................................ 25

4.2

Oil Level Check and Oil Change for Cutterbar .................................................................... 26

4.3

Oil Level Check and Oil Change for Main Gearbox ............................................................ 26

4.4

Oil Level Check and Oil Change for Gearbox, Mower Drive/Conditioner Drive ................. 27

4.5

Oil Level Check and Oil Change for the 1000 rpm power take off ...................................... 27

4.6

Unlocking the Overload Coupling on the Drive Shaft to the Cutterbar
and on the Conditioner Drive (Walterscheid) ...................................................................... 28

4.7

Preparing the overload clutch for use (ByPy) ..................................................................... 28

4.8

Bleeding the overload clutch of the universal joint drive shaft
and of the double joint ......................................................................................................... 28

4.9

Lubrication ........................................................................................................................... 29

5.

Conditioner and Protective Cloth Covers ....................................................................... 31

6.

Wide swath hood ............................................................................................................... 32

7.

Winter Storage ................................................................................................................... 34

8.

Start-up after Winter Storage ........................................................................................... 34

Supplement to Operating Instructions

1. Assembly Instructions (initial installation) ........................................................................ 39
2. Mounting the Gearbox for a 1000 rpm Power Take-Off Shaft ......................................... 50

Содержание AM 203 CV

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды