manualshive.com logo in svg

Krone AM 203 CV, Руководство по эксплуатации

Поделиться
Скачать
Krone AM 203 CV Скачать руководство пользователя страница 28

26

4.3 Oil Level Check and Oil Change for

Main Gearbox

Oil Change

An oil change should be carried out after approx.
350 hectares of operation. Bring the disc mower to the
transport position and secure with the transport safety
device. Unscrew the oil drain screw (2) and the oil
check screw (1) on the cutterbar. Collect the used oil
(approx. 4–6 litres) in a suitable container. When the oil
has drained, insert the oil drain screw again. Fill up to
the oil control holes (1) with new oil. Insert the oil check
screw with a ring seal. Close the oil check hole with the
screw. For oil quantities and oil types, please refer to
the chapter “Technical Data”.

Bring the disc mower into the working position before
checking the oil. Underneath the breather connection
(1) you can see the oil check hole (2) and the drain
screw (3) in the adjacent diagram. To check the oil, take
the screw out of the oil check hole. The oil in the main
gearbox must come up to the check hole. Top up with
oil if necessary.

NOTE: Change oil in the main gearbox after the first
use and then every 350 hectares.

When changing oil, take out the drain screw and the
check screw. Drain the oil (approx. 0.4 litres) into a
suitable container. Replace the drain screw and fill up to
the check hole with oil. For information on quantities and
types of oil, please refer to the chapter “Technical Data”.

Dispose of used oil in the correct way
after every oil change!

After an oil change, the used oil must be
disposed of in the correct way!

4.2 Oil Level Check and Oil Change for

Cutterbar

When checking the oil in the cutterbar,
always ensure that the cutterbar is
secured by the transport safety device.
High risk of injury!

Oil Level Check

To check the oil level in the cutterbar, first move it to
transport position and secure with the transport safety
device. Unscrew the oil level check screw (1)
on the side of the cutterbar. The oil level in the cutterbar
must reach up to the oil check hole.
Refill if necessary.

Check the oil level regularly every 100 operating hours!

AM-1-092

3

2

1

Содержание AM 203 CV

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды