manualshive.com logo in svg

Krone AM 203 CV, Руководство по эксплуатации

Поделиться
Скачать
Krone AM 203 CV Скачать руководство пользователя страница 22

20

3.6 Adjusting the Swath Width

The swath width is adjusted by means of swath
deflector plates (1) located under the swath hood
on the mower. These can be adjusted by loosening
the ring nuts (2) in the slot area. Fasten the ring nuts
securely again after making the adjustment.

1

2

AM-1-065 

1

AM-1-053 

3

2

AM-4-100

-3

0

+3

+6

-6
-9

+9

5

4 

The weight of the disc mower would normally make it
very difficult to adjust the cutting height from the upper
link arm.The cutting height is adjusted using a crank (3).
The inclination of the disc mower and therefore also the
cutting height are adjusted at the top link arm coupling
point (1) using a threaded spindle (2).

The lower link arm must be fixed to the
tractor with chains or bars so that the
mower does not swing out during
transport or mowing!

3.7 Adjusting the cutting height

The adjustment can be checked using the inclinometer
(4) (air level) located on the conditioner housing. For
this move the mower to working position on a level area
and preset the desired cutting height on the
inclinometer.

Adjust the mower tilt by turning crank (3) until the air
level (5) of the inclinometer is in the centre between
both marks.

Indication

theoretical

Working

z. B.

cutting height

conditions

+ 6°

ca. 11 cm

Hight Cut

+ 3°

ca. 8 cm

Arable forage crop,

moist and soft ground

0°

ca. 6 cm

Arable forage crop

dry conditions

– 3°

ca. 4 cm

Normal conditions

– 6°

ca. 2 cm

Setting the mower to low

risk of sward damage

Содержание AM 203 CV

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды