KROHNE ifc 300 Скачать руководство пользователя страница 98

Страница: 98 / 140

OPERATION

IFC 300

www.krohne.com

06/2009 - 4000069802 - MA IFC 300 R03 en

No.

Function

Settings / descriptions

C1.3 self test

C1.3

self test

C1.3.1

empty pipe detect

Switch conductivity measurement off and on (measurement of the electrode

resistance).

Select: off

conductivity (only conductivity measurement)

cond. + empty pipe [F] (conductivity measurement and empty pipe indication,

error category [F] application);

Flow indication "= 0" when pipe empty

cond. + empty pipe [S] (conductivity measurement and empty pipe indication,

error category [S] measurement outside of specification);

Flow indication "

≠

0" when pipe empty

C1.3.2

limit empty pipe

Only available when empty pipe activated [..] in Fct. C1.3.1

Range: 0.0

…

9999

S (set max 50% of the lowest occurring conductivity in

operation. Conductivity below this value = signal as empty pipe)

C1.3.3

act. conductivity

Only available when empty pipe activated [..] in Fct. C1.3.1

Current conductivity is indicated. Activation takes place only after setting

mode is exited!

C1.3.4

full pipe detect

Only for measuring sensors with 3 (4) electrodes.

Select: off (no full pipe measurement) / on (full pipe measurement by 3rd

electrode)

C1.3.5

limit full pipe

Only when full pipe detection activated, see Fct. C1.3.4.

Range: 0.0

…

9999

S (conductivity over this value = signal as full pipe)

C1.3.6

linearity

Only if GK values "GK+GKL" are activated with Fct. C1.1.3 (check carried out

with 2 field currents).

Select: off (no linearity check) / on (linearity check activated)

C1.3.7

act linearity

Only available when linearity test "on" activated in Fct. C1.3.6. The

conductivity measurement must also be activated, see Fct. C1.3.1.

Activation takes place only after setting mode is exited!

C1.3.8

gain

Automatic test switched off / on, select: off / on

C1.3.9

coil current

Automatic test switched off / on, select: off / on

C1.3.10

flow profile

Automatic test switched off / on, select: off / on

C1.3.11

limit flow profile

Only with flow profile switched on, see Fct. C1.3.10.

Range: 0.000

…

10 (absolute values above this threshold generate an error of

category [S])

C1.3.12

act. flow profile

Only available when flow profile "on" activated in Fct. C1.3.10. Activation

takes place only after setting mode is exited!

C1.3.13

electrode noise

Automatic test switched off / on, select: off / on

C1.3.14

limit electr. noise

Only with electrode noise activated, see Fct. C1.3.13.

Range: 0.000

…

12 m/s (noise above this threshold generates an error of

category [S])

C1.3.15

act. electr. noise

Only available when electrode noise "on" activated in Fct. C1.3.13. Activation

takes place only after setting mode is exited!

C1.3.16

settling of field

Automatic test switched off / on, select: off / on

.book Page 98 Wednesday, June 10, 2009 4:20 PM

Содержание ifc 300













































































































































Результаты поиска

Содержание ifc 300

Отзывы:

Похожие инструкции для ifc 300

Бренды по названию

Популярные бренды

KROHNE ifc 300, Руководство пользователя

Результаты поиска

Содержание ifc 300

Отзывы:

Похожие инструкции для ifc 300

Бренды по названию

Популярные бренды