KROHNE ifc 300 Скачать руководство пользователя страница 41

Страница: 41 / 140

ELECTRICAL CONNECTIONS

IFC 300

www.krohne.com

06/2009 - 4000069802 - MA IFC 300 R03 en

4.5.1 Connecting the signal and field current cables, field housing

•

The outer shield of signal cable A and/or B is connected electrically with the housing via the
clip of the strain relief.

•

If a shielded field current cable is used, the shield must NOT

NOT

NOT be connected to the device.

•

Bending radius:

≥

50 mm / 2"

Remove the locking screw and open the housing cover.

Pass the prepared signal and field current cables through the cable entries and connect the

corresponding stranded drain wires and conductors.

Secure the field current cable using the clip. Any shield that is present must NOT

NOT

NOT be connect-

ed.

Secure the signal cable using the clip. This also connects the outer shield to the housing.

Close the housing cover and secure it with the locking screw.

Figure 4-13: Electrical connection of the signal and field current cables, field housing

INFORMATION!

Each time a housing cover is opened, the thread should be cleaned and greased. Use only resin-
free and acid-free grease.
Ensure that the housing gasket is properly fitted, clean and undamaged.

.book Page 41 Wednesday, June 10, 2009 4:20 PM

Содержание ifc 300













































































































































Результаты поиска

Содержание ifc 300

Отзывы:

Похожие инструкции для ifc 300

Бренды по названию

Популярные бренды

KROHNE ifc 300, Руководство пользователя

Результаты поиска

Содержание ifc 300

Отзывы:

Похожие инструкции для ifc 300

Бренды по названию

Популярные бренды