KROHNE ifc 300 Скачать руководство пользователя страница 42

Страница: 42 / 140

ELECTRICAL CONNECTIONS

IFC 300

www.krohne.com

06/2009 - 4000069802 - MA IFC 300 R03 en

4.5.2 Connecting the signal and field current cables, wall-mounted housing

•

The outer shield of signal cable A and/or B is connected via the stranded drain wire.

•

If a shielded field current cable is used, the shield must NOT

NOT

NOT be connected to the device.

•

Bending radius:

≥

50 mm / 2"

Open the housing cover.

Pass the prepared signal cable through the cable entry and connect the corresponding strand-

ed drain wires and conductors.

Connect the stranded drain wire of the outer shield.

Pass the prepared field current cable through the cable entry and connect the corresponding
conductor.
Any shield that is present must NOT

NOT

NOT be connected.

Tighten the screw connections of the cable entry and close the housing cover.

Figure 4-14: Electrical connection of the signal and field current cables, wall-mounted housing

INFORMATION!

Ensure that the housing gasket is properly fitted, clean and undamaged.

.book Page 42 Wednesday, June 10, 2009 4:20 PM

Содержание ifc 300













































































































































Результаты поиска

Содержание ifc 300

Отзывы:

Похожие инструкции для ifc 300

Бренды по названию

Популярные бренды

KROHNE ifc 300, Руководство пользователя

Результаты поиска

Содержание ifc 300

Отзывы:

Похожие инструкции для ifc 300

Бренды по названию

Популярные бренды