Krendl 5200-P Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 36

Krendl 5200-P Скачать руководство пользователя страница 10

Rev. Date: 12/14/10

Page 7

MODEL #5200-P

Rotating parts will be moving in this direction.

KMC-01234

Part number for identification and tracking.

Operating machine at specified voltage will result
in longer machine life and better performance.

Identifies if machine is in remote mode, manual
mode, or off position. In manual mode this switch
operates machine. In remote mode the hand
pendant operates machine. Each time machine
cycle starts, an audible alarm warns the opera-
tor that the machine is about to come on.

Indicates that this outlet is intended for only the
wireless remote. Each time machine cycle
starts, an audible alarm warns the operator that
the machine is about to come on.

Indicates that this outlet is intended for only the
remote control outlet. Each time machine cycle
starts, an audible alarm warns the operator that
the machine is about to come on.

Keeping the door closed will keep bystanders
safe from rotating parts.

Indicates if the latches on the access door are
locked or unlocked

«
...
8
9
10
11
12
...
»

Содержание 5200-P





































Отзывы:

Нет отзывов