background image

36 

 

THIS  LIFETIME  WARRANTY  COVERAGE  WILL  BE  EXTENDED  AS  DESCRIBED  BELOW  PROVIDED  ALL  WARRANTY 
CONDITIONS AND REQUIREMENTS ARE MET AS OUTLINED IN THE 10 YEAR LIMITED WARRANTY POLICY. 

LIFETIME  WARRANTY  IS  EXTENDED  AS  FOLLOWS

:    Hussong  Manufacturing    Co.,  Inc.  warranties  to  the  original 

purchaser that the firebox, heat exchanger, fiber logs, burner tube and glass panel of this Kozy Heat Fireplace will not be defective 
in material or workmanship under normal use and service for as long as you own this product. If any of these components fail due 
to defects in material and workmanship under normal use and service, Hussong Manufacturing, Co., Inc. will, at its sole discretion, 
repair or replace the defective component. This LIFETIME WARRANTY does not cover any installation, labor, transportation or 
other indirect cost arising from defective components.  

This  Lifetime Warranty will be void if the fireplace is not installed by a qualified installer and according to the installation 
instructions. Use of unauthorized components  will make this warranty null and void. This Lifetime Warranty also is void if the 
fireplace is not operated, at all times, according to the operating instructions furnished. This warranty is limited to defects in 
material and workmanship of components specified. It does not apply to any product that has been subject to negligence, 
misapplication, improper installation. 
  
No person is authorized to extend the time of this Lifetime Warranty or to accept on Hussong Manufacturing Co., Inc.’s behalf any 
additional obligation of liability connected with the unit. 
 
Hussong Manufacturing Co., Inc. may fully discharge all obligations with respect to this Lifetime Warranty by refunding the 
wholesale price of the defective component(s). 

 

 
It is expressly agreed and understood that this Lifetime Warranty is Hussong Manufacturing Co., Inc.’s sole obligation and original 
purchaser’s exclusive remedy for defective fireplace equipment. Hussong Manufacturing Co., Inc. shall not be liable for any 
consequential, incidental or contingent damages whatsoever other than those incurred by Hussong Manufacturing Co., Inc. to 
repair or replace the defective component. The foregoing warranty is exclusive and in lieu of all other expressed warranties. 
Hussong Manufacturing Co., Inc. shall not be held to implied warranties, including but not limited to the implied warranties or 
merchantability and fitness for a particular purpose. This lifetime warranty replace all previous lifetime warranty policies. 

  

 
Hussong Manufacturing Co., Inc. reserves the right to make changes at any time, without notice, in design, material, specifications 
and prices. Hussong Manufacturing Co., Inc. reserves the right to discontinue models and products. 

  

PURCHASER NAME:   

INSTALLATION DATE:   

 

ADDRESS:   

MODEL #:   

 

   

SERIAL #:   

 

TELEPHONE:   

 

 

 

   

 

 

 

INSTALLER NAME:   

 

 

 

ADDRESS:   

 

 

 

   

 

 

 

TELEPHONE:   

 

 

 

CUT ALONG DOTTED LINE 

To activate this Lifetime Warranty coverage, this registration card must be completed and mailed with your completed 10 
Year Limited Warranty form within 30 days of installation to the following address: 
 

Hussong Manufacturing Co., Inc. 
P.O. Box 577 
204 Industrial Park Drive 
Lakefield, MN 56150-0577 

September 2011 

LIFETIME WARRANTY 

Lifetime Warranty Coverage 

Limitation of Liability 

31 

Содержание CHASKA CSK-335S


































Отзывы: