kozy heat 56150 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 36

kozy heat 56150 Скачать руководство пользователя страница 10

FRAMING

Follow vent pipe manufacturer‟s installation instructions for horizontal terminations.
Include required 1-1/2” (38 mm) top clearance (at wall pass-thru) and 1” (25 mm) sides
and bottom clearances for approved rigid vent systems.

HORIZONTAL TERMINATIONS

Follow vent pipe manufacturer‟s installation instructions for vertical terminations. A
minimum 1” (25 mm) clearance on all sides of vertical vent pipe must be maintained.

VERTICAL TERMINATIONS

IMPORTANT: Vent cap location must be in compliance with guidelines on page #17

of this manual

.

IMPORTANT:
Minimum venting: 75” (1.905 m) from floor or hearth to top of vent pipe.

IMPORTANT: WALL PASS-THRU REQUIRED FOR ALL HORIZONTAL RUNS.

REFER TO VENT MANUFACTURER‟S TO DETERMINE WHICH

PASS-THRU WILL WORK BEST FOR YOUR APPLICATION AND

WALL THICKNESS.

PAGE 9

Refer to vent pipe manufacturer‟s
instructions for specific height (H)

and width (W) framing dimensions.

75” (1.905 m) min.
to top of vent pipe

A. Locate metal bar (glass latching mechanism) below glass frame.

B. To release glass assembly, pull latch mechanism knobs out, then immediately

down, securing metal bar onto stops.

C. Pull bottom of glass assembly out, lifting up and off tabs at top of firebox.

CAST DOOR / GLASS FRAME ASSEMBLY

REMOVE GLASS FRAME ASSEMBLY

INSTALL GLASS FRAME ASSEMBLY

A. Place glass frame assembly top over tabs at top of firebox.

B. Pull bottom handles out and „up‟ to secure glass frame assembly bottom.

WARNING: DO NOT OPERATE THIS FIREPLACE WITH THE GLASS REMOVED,

CRACKED OR BROKEN. REPLACEMENT OF GLASS ASSEMBLY, #700-07T

SHOULD BE DONE BY A LICENSED OR QUALIFIED SERVICE PERSON.

WARNING: DO NOT REMOVE GLASS ASSEMBLY WHEN HOT!

Pull knobs out and

down to release.

REMOVE CAST DOOR (Breckenridge only)

Pull bottom of door out and up while lifting up to disconnect latches from mounting rod
located behind assembly.

ROD

LATCH

INSTALL CAST DOOR (Breckenridge only)

Lift door high enough to align latches above mounting rod, lowering slowly into
position.

«
...
8
9
10
11
12
...
»

Содержание 56150





































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды