background image

FREE-STANDING  

DIRECT VENT FIREPLACES 

Quality Fireplaces for Life 

January 2010 

LKFBRK-R11 

Shown with optional brushed nickel 
Prairie doors and stainless drop-in side 
inserts. 

INSTALLATION AND OPERATION MANUAL 

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE. 

 

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

 

www.kozyheat.com 

 

  

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other  

 

     appliance. 

 

 IF YOU SMELL GAS: 

 

  Do not light any appliance. 

 

  Do not touch any electrical switch: do not use any phone in your building. 

 

  Immediately call gas supplier from a neighbors phone.  Follow the gas supplier instructions. 

 

  If you cannot reach your gas supplier, call the fire department. 

         

  Installation and service must be performed by a qualified installer, service agency or the gas

 

supplier.

 

WARNING:  If the information in these instructions are not followed exactly, a fire or explosion may        
 

 

        result, causing property damage, personal injury or loss of life. 

This appliance is only for use with the type (s) of gas indicated on the rating plate. A conversion kit is supplied 
with the appliance. 

This appliance may be installed in an aftermarket permanently located, manufactured (mobile) home, where not prohibited by local codes.  
A manufactured home (USA only) or mobile home OEM installation must conform with the 

Manufactured Home Construction and Safety Standard, 

Title 24 CFR, Part 3280, 

or when such a standard is not applicable, the Standard for 

Manufactured  Home Installations, ANSI/NCSBCS A225.1, 

 or 

Standard for 

Gas Equipped Recreational Vehicles and Mobile Housing, CSA Z240.4 

WARNING 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

HOT GLASS 

 WILL CAUSE BURNS. 

 

DO NOT TOUCH 

 GLASS UNTIL COOLED. 

 

NEVER 

ALLOW CHILDREN TO TOUCH GLASS. 

 

WARNING:   This product must be installed by a licensed plumber or gas fitter when installed in the  

 

 

          

commonwealth of Massachusetts. 

BRECKENRIDGE 

LAKEFIELD

 

DO N

OT

  

DISC

ARD

 

Содержание 56150





































Отзывы: