background image

FREE-STANDING  DIRECT  VENT  GAS  FIREPLACE  

I N S TA L LA T IO N   M A NUA L

 

www.kozyheat.com 

     WARNING 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

HOT GLASS 

WILL CAUSE BURNS. 

DO NOT TOUCH 

GLASS UNTIL COOLED. 

NEVER 

ALLOW CHILDREN TO TOUCH GLASS. 

 

Do not store or use gasoline or other flammable vapors and liquids in the vicinity  

 

   of this or any other appliance.   

 

 WHAT TO DO IF YOU SMELL GAS: 

 

  Do not try to light any appliance. 

 

  Do not touch any electrical switch: do not use any phone in your building. 

 

  Immediately call gas supplier from a neighbors phone.  Follow the gas supplier 

 

     instructions.   

 

  If you cannot reach your gas supplier, call the fire department. 

      

 

    — Installation and service must be performed by a qualified installer, service         
 

 agency or the gas supplier.

 

WARNING:  If the information in these instructions is not followed exactly, a fire 
or  explosion  may result  causing  property  damage,  personal  injury or  loss  of  life. 

This  appliance  may  be  installed  in  an  aftermarket  permanently  located,  
manufactured home (USA only) or mobile home, where not prohibited by local codes. 

 

This appliance is only for use with the type of gas indicated on the rating plate. This 

appliance  is  not  convertible  for  use  with  other  gases,  unless  a  certified  kit  is  used. 

INSTALLER:  Leave this manual with the appliance.

 

CONSUMER:  Retain this manual for future reference.

 

IMPORTANT: 

This  installation  manual  is  to  be  used  in  conjunction  with  SUPPLEMENTAL  

INSTALLATION  AND  HOMEOWNER  INFORMATION  MANUAL.  Read  both  manuals  before  installing 
and operating appliance.   

JULY 2012 

LKF-REV-12-SEPARATE 

English and French Installation Manuals Available Through Your Local Dealer or Visit Our Website at www.kozyheat.com 

 

Les  manuels  d’installation  en  anglais  et  en  français  sont  disponibles  chez  votre  détaillant  local  ou  en  visitant  notre  site  Web 

:  www.kozyheat.com 

Содержание 56150









































Отзывы: