Korg M50-73, Руководство по параметрам

Страница: 397 / 419

M50 and MIDI CCs Responses to standard MIDI controllers
389
You can assign any control change number (CC#00–119) to
the Realtime Control Knobs 1-B – 4-B. In this case, the
transmitted values will all be 0…127.
You can assign any control change number (CC#00–119) to
the ARP ON/OFF switch, arpeggio control knobs 1–4. In
this case, ARP switches will transmit values of 0 (Off) or 127
(On), knobs 1–4 will transmit values of 0…127.
*1 In the M50 sequencer, bank select messages are normally
specified as program change events (“MIDI Event Edit”
Sequencer P6). However in some cases this will be
insufficient when you wish to change banks on an
external device. In such cases, you can use CC#00 and
CC#32 to specify the banks.
For information on the relation between bank select
numbers and the banks of your external device, refer to
the owner’s manual for your external device.
*2 Unlike conventional control changes, pitch bend range,
fine tune, and coarse tune settings are made using RPC
(Registered Parameter Control) messages. In Program,
Combination, and Sequencer modes, you can use RPC
messages to control the bend range and tuning for each
program, Timbre (Combination), or Track (Sequencer).
The procedure is to use an RPN (Registered Parameter
Number) message to select the parameter that you wish
to edit, and then use Data Entry to input a value for that
parameter. To select the parameter, use CC#100 (with a
value of 00…02) and CC#101 (with a value of 00). use
CC#06 and CC#38 to enter the data.
The data entry values for each parameter and the corre-
sponding settings are as follows.
For example, if in Sequencer mode you wish to set a
MIDI track that is receiving channel 1 to a transpose
(coarse tuning) value of –12, you would first transmit
[B0, 64, 02] (64H=CC#100) and [B0, 65, 00] (65H=CC#101)
to the M50 to select the RPN coarse tune. Then you
would set this to –12 by transmitting [B0, 06, 34]
(06H=CC#6), 34H=52 (corresponds to –12), and [B0, 26,
00] (26H=CC#38, 00H=0).
*3 The volume of the M50 is determined by multiplying the
Volume (CC#07) with the Expression (CC#11). In
Sequencer mode when you stop the song playback and
return the location to the beginning of the track, the
Volume will be set to the starting value, and the
81 SW2 modulation On/Off
0…63(Off ),
64…127(On)
corresponds to on/off when the SW2 function is set to SW2 Mod.
82 Foot switch On/Off
0…63(Off ),
64…127(On) corresponds to on/off when the function of the assignable foot switch is set to
Foot SW
83 Controller (CC#83) 0…127 for controlling AMS or Dmod
84 – – –
85…88 Controller (CC#85…88) 0…127 for controlling AMS or Dmod
89, 90 – – –
91 Effect depth 1 (send 2 level) 0…127 send 2 level
92
Effect depth 2 (Insert Effect 1–5 On/
Off ) 0…63(Off ),
64…127(On)
turn Insert effect 1…5 on/off *5
93 Effect depth 3 (send 1 level) 0…127 send 1 level
94
Effect depth 4 (master effect 1, 2 On/
Off ) 0…63(Off ),
64…127(On)
master effect 1, 2 on/off *5
95 Effect depth 5 (total effect On/Off )
0…63(Off ),
64…127(On)
total effect on/off *5
96 Data increment 0
97 Data decrement 0
98 NRPN(LSB) – LSB of NRPN
99 NRPN(MSB) – MSB of NRPN
100 RPN(LSB)
0 selects the pitch bend range *2
1 controls Fine Tune *2
2 controls Coarse Tune *2
101 RPN(MSB) 0 MSB of RPN
102...109 – – –
110 Chord trigger switch 1 0…127 equivalent to when CC#110 is assigned to chord trigger switch 1 *7
111 Chord trigger switch 2 0…127 equivalent to when CC#111 is assigned to chord trigger switch 2 *7
112 Chord trigger switch 3 0…127 equivalent to when CC#112 is assigned to chord trigger switch 3 *7
113 Chord trigger switch 4 0…127 equivalent to when CC#113 is assigned to chord trigger switch 4 *7
114...119 – – –
CC# Control Value Function
CC#06 CC#38
00
01
12
00
00
0
0
+ 1
+12
CC#06 CC#38
40
52
64
88
00
00
00
00
–24
–12
0
+24
CC#06 CC#38
32
48
64
96
00
00
00
00
–50
–25
0
+50
RPN=0 ( Pitch bend range )
RPN=1 (Fine tune)
RPN=2 (Coarse tune)
Parameter value (Semitone steps)
Parameter value (Semitone steps)
Parameter value (1 cent steps)