manualshive.com logo in svg

Korenix JetNet 4508 V2 Series, Руководство пользователя

Поделиться
Скачать
Korenix JetNet 4508 V2 Series Скачать руководство пользователя страница 19

 

15

 

2.7  Wiring Fast Ethernet Fiber port (JetNet 4508f V2) 

JetNet 4508f V2 equipped 2 ports fiber which compliance with IEEE 802.3 
100Base-FX standard and supports multi-mode or single mode fiber cable. 
The fiber connector supports SC type connector and for the other type 
connector, please contacts your Korenix distributor for more information. 
To ensure the quality of connection, the specifications of cable and fiber 
port must matched; with wrong fiber cable may caused the communication 
does not work well.The following information is the specification includes 
suitable cable and the characteristics of fiber port. 
 

Model 

TX power 

RX sensitivity 

Wavelength 

Fiber Cable 

JetNet 4508f-s V2, 
30KM 

-8~-15 dBm 

-31~-14dBm 

1310nm 

8~10/125 um 
Single mode 

JetNet 4508f-m V2 
2KM

 

-14~-31 dBm 

-14~-31 dBm 

1310nm 

50~62.5/125um 
Multi-mode 

 

 

2.8  Wiring RS-232 Console Cable 

There is one RS-232 DB-9 to RJ-45 cable shipped with the box. Connects 
the DB-9 connector to the COM port of your PC, open Terminal tool and 
configure the serial communication parameter to 9600, N, 8, 1. (Baud Rate: 
9600bps / Parity: None / Data length: 8bits / Stop Bit: 1) Then you can 
access CLI interface by console able. 

Note: If you lost the cable, please contact with your sales or follow the pin 
assignment to buy a new one. The Pin assignment spec is listed following. 

 

RJ-45 Pin 

DB-9 Pin 

Description 

1 7 N/A 

2 9 N/A 

3 4 TxD 

4 5 N/A 

5 1 GND 

6 3 RxD 

7 2 N/A 

8 8 N/A 

Содержание JetNet 4508 V2 Series







































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды