manualshive.com logo in svg

Korenix JetNet 4508 V2 Series, Руководство пользователя

Поделиться
Скачать
Korenix JetNet 4508 V2 Series Скачать руководство пользователя страница 120

 

116

 

4.11.6 Ping Utility 

This page provides 

Ping Utility

 for users to ping remote device and check 

whether the device is alive or not. Type 

Target IP

 address of the target 

device and click on 

Start

 to start the ping. After few seconds, you can see 

the result in the 

Result

 field.

   

 

 

 

4.11.7 CLI Commands of the Monitor and Diag 

Command Lines of the Monitor and Diag configuration 

 

Feature 

Command Line 

MAC Address Table 

Ageing Time 

Switch(config)# mac-address-table aging-time 350 
mac-address-table aging-time set ok! 

Note: 350 is the new ageing timeout value. 

Add Static Unicast MAC 
address 

Switch(config)# mac-address-table static 0012.7701.0101 

vlan 1 interface fastethernet7 

mac-address-table ucast static set ok! 

Note: rule: mac-address-table static MAC_address VLAN 
VID interface interface_name 

Add Multicast MAC 
address 

Switch(config)# mac-address-table multicast 0100.5e01.0101 

vlan 1 interface fa6-7 

Adds an entry in the multicast table ok! 

Note: rule: mac-address-table multicast MAC_address 
VLAN VID interface_list interface_name/range

 

Show MAC Address 
Table – All types 

Switch# show mac-address-table 

***** UNICAST MAC ADDRESS ***** 

Содержание JetNet 4508 V2 Series







































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды