Kontron V Panel Express 121 Скачать руководство пользователя страница 30

 

 

8. Accessing Internal Components  

V Panel Express – User’s Guide (V1.01) 

 

Legend for the figures 

Fig. 20Fig. 21, Fig. 22, Fig. 23, Fig. 24 and Fig. 26: 

1

 

Installed HDD tray (removable) 

2

 

Captive knurled screws that secure the drive tray to 
the chassis 

3

 

Location for the drive connectors (power and 
SATA) on the rear of the drive tray (if HDD is  
installed into the tray) 

4

 

Location for the 2.5" HDD drive (SATA 0) 

5

 

Location for the 2.5" HDD drive (SATA 1) 

6

 

HDD mounting screws on the left side of the drive 
tray 

7

 

2.5" SATA HDD installed as “SATA 0” into the drive 
tray 

8

 

Upper cut-out for HDD connector (power and SATA) 
for the “SATA1” drive (not included) 

9

 

Drive tray for up to two 2.5" SATAII drives 

10

 

HDD mounting screws on the right side of the drive 
tray 

11

 

Mounting holes for the second HDD (HDD is not 
included) 

 

In order to reinstall a new 2.5" SATA drive into the “SATA 0” drive location or to expand your system with a second  
2.5" SATA drive into the “SATA 1” drive location proceed as follows: 

8.

 

Remove the drive tray as described in the steps 1-7. 

9.

 

Insert the new 2.5" SATA drive into the “SATA 0” drive location or a second one into the “SATA 1” drive location (refer 
to

,

 Fig. 21,

 

pos. 3, pos. 4 and pos. 5). Fit the “SATA 0” drive location always first if your system has to be operating 

with one HDD drive only (refer to Fig. 21, pos. 4)! 

10.

 

Make sure the drive has been fitted properly into the drive tray and secure the drive using the retained screws  
(step 6). The screws for securing the second HDD (for SATA1 location) into the drive tray are not included  
(refer to Fig. 26).  

11.

 

Insert the hard disk tray into the systems HDD tray, by slightly pressing inwards. 

12.

 

Trough the access door connect inside of the unit, the SATA cable and the SATA power connector to the rear of the 
HDD (refer to Fig. 21, pos. 3).  

13.

 

Close the access door and secure it with the knurled screw (Fig. 13, pos. 2).  

14.

 

When the drive/s is/are lined up correctly, secure the drive tray to the chassis with the captive knurled screws  
(see Fig. 8, pos. 10). 

 

 

28

 

www.kontron.com

 

StockCheck.com

Содержание V Panel Express 121


















































Отзывы: