Kontron cPCI-MXS64GX, Техническое справочное руководство

Страница: 96 / 135

cPCI-MXS64GX Technical Reference Manual
4.14
4.1.11 Integrated Peripherals
Option BIOS
Defaults
Setup
Defaults
Possible
Settings
Description
On-Chip
Primary/Secondary
En. En. En./Dis.
Select Enabled to activate the Primary/Secondary IDE channel.
The four options below appear only if the On-Chip Primary option
is enabled.
On-Chip Primary IDE
Master PIO
Slave PIO
Master UDMA
Slave UDMA
Auto Auto
Auto,
Modes
0-4
Use this option to set a PIO mode (0-4) for each of the onboard
IDE devices. Modes 0 through 4 provide successively increased
performance and speed. In Auto mode, the system automatically
determines the best mode for each device. If you select a mode
that the drive does not support, it may not work, so choose a
lesser value or Auto to see the best mode for the drive.
On-Chip Secondary IDE
Master PIO
Slave PIO
Master UDMA
Slave UDMA
Dis. Auto Auto, Disabled.
Ultra DMA/33 implementation is possible only if your IDE hard
drive supports it and the operating environment includes a DMA
driver (Windows 95 OSR2 or a third-party IDE bus master driver).
If your hard drive and your system software both support Ultra
DMA/33, select Auto to enable BIOS support.
IDE HDD Block
Mode
Dis. En. En./Dis.
Block mode is also called block transfer, multiple commands, or
multiple sector read/write. If your IDE hard drive supports block
mode (most new drives do), select Enabled for automatic
detection of the optimal number of block read/writes per sector the
drive can support.
Onboard PCI SCSI
Chip
En. En. En./Dis. Enables/disables the onboard SCSI controller.
Ethernet Controller 1
and 2
En. En. En./Dis. Enables/disables the onboard Ethernet controller.
USB Keyboard
Support
OS OS OS/BIOS
This option is for DOS and BIOS support only (Win 95 has it is
own drivers).
It does not enable or disable the USB controller.
PS/2 Mouse
Function Control
Auto Auto Auto/Dis.
When set to Auto, the PS/2 mouse is automatically enabled, if it is
present.
Onboard FDC
Controller
En. En. En./Dis.
Select Disabled to disable the onboard floppy disk controller
(FDC).
Onboard Serial Port
1 3F8/
IRQ4
3F8/
IRQ4
Dis, 3F8/IRQ4,
2F8/IRQ3,
3E8/IRQ4,
2E8/IRQ3
Select a COM port address and IRQ# for Serial Port 1
Onboard Serial Port
2
Dis 2F8
3F8,2F8, 3E8,
2E8
Disabled
Select a COM port address for Serial Port 2.
IRQ Line 3 3 3,4,5,7 Sets IRQ line for serial port 2
Onboard Serial Port
3 3E8/
IRQ4
3E8/
IRQ4
Dis, 3F8/IRQ4,
2F8/IRQ3,
3E8/IRQ4,
2E8/IRQ3
Select a COM port address and IRQ# for Serial Port 3
Serial Port 3 Mode RS-232 RS-232
RS-232 RS-422
RS-485
Select the operation mode for Serial Port 3.
Onboard Serial Port
4
Dis 2E8
3F8,2F8, 3E8,
2E8
Disabled
Select a COM port address for serial port 4.
IRQ Line 3 3 3,4,5,7 Sets the IRQ line for serial port 4.
Onboard Parallel
Port
378/ IRQ7
378/
IRQ7
Select a LPT address and IRQ# for the physical parallel (printer)
port. Possible settings are:
Disabled, 3BC/IRQ7, 378/IRQ7, 278/IRQ5,
Parallel Port Mode
ECP
+
EPP1.9
ECP
+
EPP1.9
Select an operating mode for the onboard parallel port. Select
ECP or EPP unless you are certain both your hardware and
software does not support ECP or EPP mode.
Possible settings are SPP, EPP1.9+SPP, ECP, ECP+EPP1.9,
Normal, EPP1.7+SPP, ECP+EPP1.7
ECP Mode Use DMA 3 3 1, 3 Select a DMA channel for the parallel port.