101
Measurement
Before starting measurement, perform the following.
Connection
(P. 58)
Connect the power cable and turn ON the power.
Measurement
Preparation
(P. 65)
Perform preparations (instrument setting, zero calibration) that are required prior to
measurement.
Settings
(P. 106)
Set up the instrument according to the setting method.
This is not necessary if the instrument has already been set up or if measurement will
be performed using Konica Minolta’s calibration standard.
1. Performing Measurement
Operating Procedure
1
Press the [CAL CH] key to select a probe
and a calibration channel. (Not required
in flicker mode)
Select Probe
01
02
03
04
05
06
07
08
09
10
Select User Calb CH
C H 0 0 1 6 0 . 0
0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
C H 0 1 1 6 0 . 0
0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
C H 0 2 1 6 0 . 0
0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
C H 0 3 1 6 0 . 0
0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
C H 0 4 1 6 0 . 0
0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
C H 0 5 1 6 0 . 0
0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
C H 0 6 1 6 0 . 0
0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
C H 0 7 1 6 0 . 0
0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
C H 0 8 1 6 0 . 0
0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
C H 0 9 1 6 0 . 0
0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
(1) Press the [CAL CH] key.
(2) Press the [UP]/[DOWN] key to select
a probe (01 to 10) and then press the
[ENTER] key.
Select Probe > Select CH
01
Select User Calb CH
◉
C H 0 0 1 6 0 . 0
0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
○
C H 0 1 1 6 0 . 0
0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
○
C H 0 2 1 6 0 . 0
0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
○
C H 0 3 1 6 0 . 0
0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
○
C H 0 4 1 6 0 . 0
0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
○
C H 0 5 1 6 0 . 0
0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
○
C H 0 6 1 6 0 . 0
0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
○
C H 0 7 1 6 0 . 0
0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
○
C H 0 8 1 6 0 . 0
0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
○
C H 0 9 1 6 0 . 0
0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
Calibration Value
f KM factory calibration value
“----”
c
User calibration
(with set correction coefficients)
“----”
s Single-point calibration
Single-point
calibration value
m RGB+W matrix calibration
White calibration value
(3) Press the [UP]/[DOWN] key to select
a calibration channel (CH00 to 99),
and then press the [ENTER] key.
The calibration coefficient for the selected
calibration channel is applied.
2
Place the probe flat against the display
and perform measurement.
The measurement results will be displayed in the
selected data display area.
CA
-DP40
Measur
ement
Содержание CA-410 Series
Страница 12: ......
Страница 40: ......
Страница 139: ......
Страница 140: ...En 9222 AA1J 12 2017 KONICA MINOLTA INC BIFBDA...