Kongskilde GXS 9005 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 70

background image

2. CONNECTION AND TEST DRIVING

PIGB-183X 04 GXS 9005 / P 0218

27

TEST DRIVING

Before you use your new disc mower, please do as follows:

1.   Read this instruction manual carefully!

2.   Check that the machine has been assembled correctly and is undamaged.

3.    Check that all tools have been removed from the machine.

4.   Check  that  the  PTO  speed  of  the  machine  (and  of  the  tractor)  is  correct.  Too

high PTO speed can be dangerous. Too low PTO speed causes bad cutting,
blocking of the disc mower and high torque on the drive shafts.

5. Check the movements of the PTO drive shaft. If the PTO shafts are too short or

too long it may damage the tractor as well as the machine considerably.
Check that the protection tubes do not get jammed or damaged in any position.
Check that the safety chains of the protection tubes have been secured properly
and that they do not in any position get too tight or damaged.

6. Make sure that the hydraulic hoses have been connected in such a way that

they are long enough for the movements of the machine in relation to the
tractor.

7. Check that the machine has been greased sufficiently and check that the oil

level in the gearbox and the cutterbar is correct. See section

”4. GREASING”.

8. Air the friction clutch as described in chapter

5 "MAINTENANCE".

9. From the factory the revolving parts of the machine have been tested and

declared error-free. However, you should do as follows before using the
machine:

Start the machine at a low number of RPM. With open rear window and without

hearing protector you should check that there are no unusual scratching or
knocking sounds. Then the number of RPM can be increased. At the correct
number of RPM, check if there are any noticeable vibrations. (Check the guards
for unusual vibrations).

«
...
25
26
27
28
29
...
»

Содержание GXS 9005







































































Отзывы:

Нет отзывов

Похожие инструкции для GXS 9005

Бренд: Bartscher Страницы: 22

Бренд: Ocmis Irrigazione Страницы: 100

Бренд: tayco Страницы: 111

Бренд: Pahlen Страницы: 20

Бренд: Paia Страницы: 7

Бренд: Olympus Страницы: 130

Бренд: M-system Страницы: 4

Бренд: Waves Страницы: 8

BOMAG BW 120 AD-5

Бренд: Fayat Страницы: 210

Levitator III F-LHLEV3

Бренд: Skytron Страницы: 248

Бренд: Viavi Страницы: 404

ARCHISHAPE 2.0 Linear

Бренд: Osram Страницы: 7

Бренд: ASIA TECHNOLOGY Страницы: 38

LED Niova 150-F Pro 150W Bi Color

Бренд: Walimex Pro Страницы: 56

Бренд: Sport-thieme Страницы: 20

Бренд: Ground Fault Systems Страницы: 26

Бренд: Oromed Страницы: 64

Quest Enterprise Activity Unit QU10

Бренд: Play & Leisure Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды