Kongskilde GXS 9005 Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 70

background image

6. MISCELLANEOUS

PIGB-183X 04 GXS 9005 / P 0218

64

6. MISCELLANEOUS

DRIVING TIPS AND FAULT-FINDING

Problem

Possible cause

Remedy

Uneven stubble or bad cut

The number of rpm of the tractor is too
low.

The blades are worn

Discs, stone protectors or flow caps are
deformed.

The ground pressure is too low.

Check  that  the  number  of  rotations  of  the
tractor  PTO  is  correct.  Keep  a  constant
number of RPM

Turn/move the blades to another disc or
replace the blades

Replace deformed parts.

Adjust the relief

– increase the ground

pressure.

Stripes in stubble

The cutting angle is too large, the grass
is not transported across the cutterbar

Accumulation  of  material  in  front  of  the
cutterbar

Earth  and  grass  around  the  cutterbar
between the discs

You  are  working  early  in  the  morning
when the grass is still very wet

Adjust the cutter bar more horizontal by
lengthening the top link

Increase the driving speed, if possible

Replace worn shearbars.

Increase the driving speed, if possible

Irregular flow through the machine

Conditioner  fingers  may  be  worn  or
missing

The  distance  between  the  conditioner
plate  and  the  conditioner  rotor  is  too
long

Replace worn fingers and mount new ones
where these are missing

Adjust the conditioner plate to shorter
distance to the rotor
Increase the driving speed

The

machine

vibrates/

uneven

operation

Blades may be deformed, damaged or
missing

Defective PTO drive shafts

Defective bearings in cutter bar or
conditioner rotor

Replace damaged blades and mount new
ones where these are missing

Check if the shafts are intact. Repair, if
necessary

Check if bearings are loose or damaged.
Replace if necessary

Gear or cutterbar overheated

Oil level not correct

Check the oil level and refill/drain out oil, if
necessary

REMEMBER:

Gearbox

temperature

maximum 80 °C, cutterbar temperature
maximum 90-100 °C.

Power consumption unusually high

Crop and dust under the discs

String or wire is wrapped around a disc.

Stop the tractor engine. Dismount the discs
and clean cutter bar and discs.

Check if the friction clutch is intact.

Remove the foreign matter.

«
...
62
63
64
65
66
...
»

Содержание GXS 9005







































































Отзывы:

Нет отзывов

Похожие инструкции для GXS 9005

Бренд: Taber Страницы: 27

Бренд: Landoll Страницы: 83

Бренд: C.M.O Страницы: 10

Бренд: lancer Страницы: 12

Бренд: JB Systems Страницы: 12

Growers Supply 109722

Бренд: FarmTek Страницы: 9

Бренд: Rane Страницы: 6

Бренд: Rane Страницы: 27

Бренд: Ranger Products Страницы: 6

Бренд: Rane Страницы: 88

Бренд: Haag-Streit Страницы: 21

Бренд: Safavieh Страницы: 2

Бренд: Vendlet Страницы: 2

Бренд: Yamaha Страницы: 29

Бренд: HAGS Страницы: 17

UniPlay Congaree

Бренд: HAGS Страницы: 11

STOMAMED COL-160

Бренд: Orliman Страницы: 12

Бренд: Gardol Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды