Kongskilde GXS 9005 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 70

background image

3. DRIVING AND OPERATION

PIGB-183X 04 GXS 9005 / P 0218

34

DANGER:

Transport height

Before transporting the machine on public road, make sure that the
transport height of 4.0 m is not exceeded.

Folding of the machine to vertical transport position takes place as follows:

1. Stop the PTO and wait until all revolving parts have stopped.
2.

Activate the tractor’s hand brake.

3.  Fold up the side guards and clean the machine, if necessary.
4.  Pull the cord for the transport safety device.
5.  Fold  up the machine to approx.  45° hydraulically

– let go of the cord and lift

the machine further until the transport safety device is engaged.

6. Lower the link arms of the tractor so that the hitch pins are approx. 25 cm

above the ground.

7. Close all hydraulic stop cocks and check that the transport safety device is

engaged.

WARNING:

Lowering of the 3-point suspension

When the machine is lowered in the 3-point suspension, it must be
checked, that the machine does not touch parts on the tractor.

«
...
32
33
34
35
36
...
»

Содержание GXS 9005







































































Отзывы:

Нет отзывов

Похожие инструкции для GXS 9005

Бренд: York Fitness Страницы: 34

LOUDEN 200 Series

Бренд: ACCO Brands Страницы: 144

Бренд: B&K Страницы: 16

Бренд: B&G Страницы: 2

Бренд: Federal Страницы: 43

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 20

Бренд: Qu-Bit Electronix Страницы: 15

Бренд: Tactile Medical Страницы: 23

Бренд: Taarup Страницы: 72

Бренд: Valmar Страницы: 78

Бренд: Valhalla Scientific Страницы: 64

Бренд: mychway Страницы: 56

LUXOMAT net PBM-KNX-DX-4W

Бренд: B.E.G. Страницы: 16

Бренд: EuroLite Страницы: 2

Бренд: ATD Tools Страницы: 7

SPLICE-500 MKII

Бренд: Serpent Страницы: 8

Бренд: Wecan Technology and Lighting Co., Ltd Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды