background image

 

19

I/O Terminal / 

MANUAL CONFIGURATION

 

 

Bit 

Bit 

Function 

adjustable in the feature register 
(default). 

Cnt_Set 

The counter is set to the value that is 
specified via the process data with the 
rising edge of Cnt_Set. 

En_Latch_Ext 

The external latch input is activated for 
positive edge. With the first external 
latch impulse after validity of the 
En_Latch_Ext bit, the counter value in 
the latch register is stored. The pulses 
that follow have no influence on the 
latch register when the bit is set. 
Attention must be paid to ensuring that 
the corresponding latch valid bit 
(Latch_Ext_Val) has been removed 
from the terminal before alerting of the 
zero pulse. This functionality is 
adjustable in the feature register 
(default). 

RD_Period 

The periods between two positive 
edges of the input A are measured with 
a resolution of 200 ns. When the bit is 
set, this period is output in the data 
bytes D2, D3, D4. This functionality is 
adjustable in the feature register. 

En_Latch 

The zero point latch (C input) is 
activated. The counter value is stored in 
the latch register with the first external 
latch pulse after validity of the En_Latch 
bit (this has priority over En_Latch_Ext). 
The pulses that follow have no 
influence on the latch register when the 
bit is set. Attention must be paid to 
ensuring that the corresponding latch 
valid bit (Latch_Val) has been removed 
from the terminal before the zero pulse 
is alerted (the Latch_Val bit cannot be 
removed from the terminal until the C 
pulse has a low level). 

Note:

 For the external latch input: The activation of the positive edge (En_Latch_Ext = 1) has 

priority to the activation of the negative edge (En_Latch_Ext_n = 1). 

Содержание AKT-ENC-000-000






























Отзывы: