Kohler Rada 215 Series Скачать руководство пользователя страница 18

Страница: 18 / 32

1057616-W2-J

Make sure that the hot and cold supplies have

been connected to the correct inlets, and that

all connections are watertight.

Refer to section:

‘Commissioning’

OPERATION

For adjustable temperature models adjustment of

the blend temperature from the preset maximum

to cold is achieved by clockwise rotation of the

temperature knob.
For locked temperature models no user adjustment

is intended.

Control of flow is via a separate outlet valve(s),

refer to section:

‘Specifications’

Adjustable Temperature Models Only

Hot

Cold

COMMISSIONING

Commissioning must be carried out in accordance

with these instructions, and must be conducted by

designated, qualified and competent personnel.

Exercising the Thermostat

Thermostatic mixing valves with wax thermostats

are inclined to lose their responsiveness if not

used. Valves which have been in storage, installed

but not commissioned, or simply not used for

some time should be exercised before setting the

maximum temperature or carrying out any tests.
A simple way to provide this exercise is:

(a)

Make sure that the hot and cold water

are available at the valve inlets, and the

outlet is open.

(b)

Move the temperature control rapidly from

cold to hot and back to cold several times,

pausing at each extreme.

Maximum Temperature

Note!

For Type 3 healthcare installations the

maximum blend temperature is determined by

the application, refer to the

'TMV3 Requirements

Manual'

The maximum blend temperature obtainable by

the user should be limited, to prevent accidental

selection of a temperature that is too hot.
All Rada thermostatic mixing valves are fully

performance tested and the maximum temperature

is preset to approximately 41°C (222 models -

44°C) under ideal installation conditions at the

factory.
Site conditions and personal preference may

dictate that the maximum temperature has to be

reset following installation.
This mixing valve is provided with two methods

of temperature setting, an adjustable temperature

control knob which allows the user to select the

blend temperature between ambient cold up

to a preset maximum, or if considered more

appropriate, a locked cap can be fitted, allowing

no user adjustment.

Содержание Rada 215 Series

































Результаты поиска

Содержание Rada 215 Series

Отзывы:

Похожие инструкции для Rada 215 Series

Бренды по названию

Популярные бренды

Kohler Rada 215 Series, Руководство по эксплуатации продукта

Результаты поиска

Содержание Rada 215 Series

Отзывы:

Похожие инструкции для Rada 215 Series

Бренды по названию

Популярные бренды