background image

6

Valve Combinations

These thermostatic mixers are available with various shower fittings and water saving features, refer to 

the table below to identify your mixer valve combination:

Mixer Valve

Shower 

Fittings

Flow Regulator

Flow Rate

Colour

Comments

Moto EV /
Minilite EV

L14A

12 L/Min

Red

Supplied in the component pack, designed to 

be fitted in the shower valve outlet

Pace EV /
Miniduo EV

L98B

12 L/Min

Red

Supplied in the component pack, designed to 

be fitted in the shower valve outlet

Minilite BIV

L14A

12 L/Min

Natural

Supplied in the component pack, designed 

to be fitted between the shower hose and 

RAC assembly

Minilite Eco EV

L14A

6 L/Min

Black

Factory  fitted  in  the  shower  valve  outlet 

(optional 8 L/Min (white/natural) flow 

regulator supplied separately in the 

component pack)

Minilite Eco BIV

L14A

6 L/Min

Black

Factory fitted in the RAC assembly (optional 

8 L/Min (white/natural) flow regulator 

supplied separately in the component pack)

Miniduo BIV

L98B

12 L/Min

Natural

Supplied in the component pack, designed 

to be fitted between the shower hose and 

RAC assembly

Pace BIV

L14D

P a c e   E V   w i t h 

Adjustable Elbows

L14D

12 L/Min

Red

Supplied in the component pack, designed to 

be fitted in the shower valve outlet

P a c e   w i t h   E c o 

Showerhead EV

L98B with Eco 

Showerhead

7.0 L/Min

Olive Green

Supplied in the component pack, designed 

to be fitted between the shower hose and 

shower valve outlet

Miniduo with Eco 

Showerhead EV

L98B with Eco 

Showerhead

7.0 L/Min

Olive Green

Supplied in the component pack, designed 

to be fitted between the shower hose and 

shower valve outlet

Miniduo with Eco  

Showerhead BIV

L98B with Eco 

Showerhead

7.0 L/Min

Olive Green

Supplied in the component pack, designed 

to be fitted between the shower hose and 

RAC assembly

Miniduo with Eco 

Showerhead BIR

Eco BIR 

Showerhead

7.3 L/Min

Bright 

Green

Supplied with the Eco BIR shower head, 

designed to be fitted between the wall plate 

and inlet nipple

Flow regulators are supplied for installation on high pressure systems (above 0.5 bar).

For gravity fed or other low pressure systems do not fit the flow regulator.
The Mira Minilite Eco has a flow regulator factory fitted in the shower valve outlet or RAC assembly, 

on older combination boiler systems it may be necessary to replace this 6 L/Min flow regulator with the 

 

8 L/Min flow regulator (supplied), in order to achieve the minimum flow rate required to ignite and run 

the boiler. 

Important! The fitting of any flow regulator to Pace and Miniduo models will invalidate TMV2 

compliance  due  to  the  minimum  flow  rate  requirements.  Do  not  fit  flow  regulators  in  TMV2 

applications to these models.

For further information on how and where to fit the flow regulator, refer to section: 

‘Flow Regulators’

.

Содержание Mira Miniduo





























Отзывы: