Kohler K-5401IN-0 Скачать руководство пользователя

Страница: 13 / 16

PREPARATIONS FORE THE FIRST USE

Confirm if both inlet hoses connection are correct.

Ensure if water inlet valve

are

OPEN.

Confirm that the battery has been correctly installed in the

"remote controller".

Confirm that there is no obstacle in front of the product.

Wait for the host to finish the self-checking. During that tim e, it is normal to hear rotating sound of the motor and

bicker. When the lighting stops flickering, the self-check is completed.

When it is used for the first time, product will be in default s tage:

Front:

●

Water temp: mid
Pressure: mid
Position: level 3

Rear:

●

Water temp: mid

●

Pressure: mid

●

Position: level 3

Spiral:

●

Water temp: mid

●

Pressure: mid

●

Pressure: mid

●

Seat temp: mid
Wind temp: mid
Night light: On
Energy saving mode: On
Function of auto cover-turning: On. Mid distance
Function of auto flushing: On
Auto UV function: On
Sterilized water function: On
Deodorization: On

Kohler Co.

1373184-IN01-A

Содержание K-5401IN-0

















Результаты поиска

Содержание K-5401IN-0

Отзывы:

Похожие инструкции для K-5401IN-0

Бренды по названию

Популярные бренды

Kohler K-5401IN-0, Руководство по установке

Результаты поиска

Содержание K-5401IN-0

Отзывы:

Похожие инструкции для K-5401IN-0

Бренды по названию

Популярные бренды