Kohler K-5401IN-0 Скачать руководство пользователя

Страница: 10 / 16

Unit: mm

Dimensions in the pictures are for reference only.

Install Deco Cover.

I nstall Angle Valve.

IMPORTANT!

Wrong inlet hoses connection sequence is not allowed.

Fig.#15

G3/4

Connect to grey water

Connect to tap water

G1/2

Fig.#16

Connect the water outlet.

Open the shut-off valve.

Connect toilet hose to angle valve A.

Connect bidet hose to angle valve B.

NOTE: Please do not reuse the old hose.

Connect the Water

IMPORTANT!

The supplied hose

must be used for this installation.

Bidet inlet

Valve B

G1/2

Back view

Toilet hose

Toilet inlet

Valve A

G3/4 supply stop

250 10

330 10

100

150

Close by rotating the handle clockwise and

open counterclockwise

Handle of angle valve

Tee valve

Decorative cover

Connect to grey water

G3/4

Connect to tap water

G1/2

NOTE: Please do not reuse the old angle valve.

G1/2 valve should be purchased by customers.

Recommend to use Kohler valve (1305032-sp).

1373184-IN01-A

Kohler Co.

Содержание K-5401IN-0

















Результаты поиска

Содержание K-5401IN-0

Отзывы:

Похожие инструкции для K-5401IN-0

Бренды по названию

Популярные бренды

Kohler K-5401IN-0, Руководство по установке

Результаты поиска

Содержание K-5401IN-0

Отзывы:

Похожие инструкции для K-5401IN-0

Бренды по названию

Популярные бренды