Kohler K-5401IN-0 Скачать руководство пользователя

Страница: 5 / 16

× 4

Fig.#5

Toilet

Hold the rim of the vitreous shell and take out the toilet.

WARNING: Risk of personal injury and product damage!Please do not hold the rim of the bidet seat when lifting the

the toilet. As the toilet is heavy, please seek help if necessary.

Overall Sketch

Crash pad

Seating sensing area

Nozzle

Press it again to turn it off.

Press Warm Wind button to start the warm wind function.

Press the button to enter Rear Wash mode.

Light sensing area

Press the button to enter Front Wash mode.

Press it again to turn it off.

Press the button to turn off the night light function (long tone hint)

Press the button to turn off the power (long tone hint)

Press it again to turn it off.

Press it again to turn on (short tone hint)

PREPARATIONS BEFORE INSTALLATION

Seat (anti-microbial)

Press the button for Flushing

Fig.#4

Cover (antibacterial)

Kohler Co.

1373184-IN01-A

Содержание K-5401IN-0

















Результаты поиска

Содержание K-5401IN-0

Отзывы:

Похожие инструкции для K-5401IN-0

Бренды по названию

Популярные бренды

Kohler K-5401IN-0, Руководство по установке

Результаты поиска

Содержание K-5401IN-0

Отзывы:

Похожие инструкции для K-5401IN-0

Бренды по названию

Популярные бренды