Kohler K-5401IN-0 Скачать руководство пользователя

Страница: 9 / 16

Nut

WARNING: Risk of personal injury. The vitreous shell weighs 35 kg. Use proper lifting technique when
handling the vitreous shell.

CAUTION: Risk of product damage. Do not set the shell down hard. Gently lift and move the shell if it is not

placed correctly. If handled harshly, the shell may chip or break.

Carefully pick up the vitreous shell.

Make sure the trap way sits fully in the outlet gasket. If the vitreous shell does not sit evenly on the floor, then the

trap way will not be properly aligned.

Make all adjustments gently reference the toilet side mark symbol and the drain hole centerline on the finished

floor until the trapway is properly seated.

Use nut and washer to fasten the bolts and fix up the toilet.

CAUTION: Risk of product damage . Do not move the toilet after the trap way is properly seated to
avoid the wax seal invalidated, Change the wax

ring

if it is needed to move.

WARNING: Risk of personal injury or product damage. Overtightening may cause breakage or chipping.

Fix Wax

Ring

Place the wax ring on the waste outlet.

Install the Vitreous Shell

Fig.#13

Fig.#14

Kohler Co.

1373184-IN01-A

Содержание K-5401IN-0

















Результаты поиска

Содержание K-5401IN-0

Отзывы:

Похожие инструкции для K-5401IN-0

Бренды по названию

Популярные бренды

Kohler K-5401IN-0, Руководство по установке

Результаты поиска

Содержание K-5401IN-0

Отзывы:

Похожие инструкции для K-5401IN-0

Бренды по названию

Популярные бренды