Kohler CURTIS 3401T Скачать руководство пользователя страница 59

Страница: 59 / 62

6 — CANopen COMMUNICATIONS

pg. 53

Return to TOC

Curtis Model 3401T – August 2022

STANDARD CANOPEN OBJECTS

The following table describes objects required by the CANopen standard:

Name

Index

Sub-Index Description

Read / Write

Values

Data Size

Device Type

1000h

00h

Indicates whether a device follows a

standard CiA device profile.

The 3401T does not follow a standard CiA

profile, so the value is 0.

32-bit

Error Register

1001h

00h

Indicates if a fault is active:

0 = No active fault

1 = One or more active faults

0–1

16-bit

Manufacturer Status

1002h

00h

Reserved.

N/A

Manufacturer Device Name

1008h

00h

Initiates a segmented SDO that uploads the

model name and number as an ASCII string.

String

Manufacturer’s Hardware

Version

1009h

00h

Initiates a segmented SDO that uploads

the hardware version as an ASCII string.

String

Manufacturer Software

Version

100Ah

00h

Reserved

Note:

The CDEV and OS Version

parameters indicate the software version.

See

Main Menu Parameters

N/A

Emergency COB ID

1014h

00h

Indicates the Emergency Message COB-ID:

• 0: The COB-ID consists of the

emergency message function code

(0001b) and the node ID.

• Non-zero: The COB-ID consists of the

emergency message function code

(0001b) and the specified value.

The COB-ID’s four most significant bits

represent the emergency message

function code.

0–16777215

32-bit

Emergency Message Inhibit

Time

1015h

00h

Sets the minimum time that must elapse

before another emergency message can

be sent.

4–100 (which

represents

16–400ms)

32-bit

Heartbeat Rate

1017h

00h

Specifies the cyclic rate of the device's

heartbeat messages.

100–1000

16-bit

Identity Object

1018h

Provides information on the device.

00h

Indicates the size of the object.

0–127

8-bit

01h

Indicates the CiA-assigned identifier of

Curtis Instruments. The identifier is 4349h.

0–2147483647

32-bit

02h

Indicates the device's product code.

0–2147483647

32-bit

03h

Indicates the device's Curtis CAN protocol

version. The upper 2 bytes contain the

major version and the lower 2 bytes

contain the minor version.

0–2147483647

32-bit

04h

Indicates the device's serial number.

0–2147483647

32-bit

Содержание CURTIS 3401T































































Результаты поиска

Содержание CURTIS 3401T

Отзывы:

Похожие инструкции для CURTIS 3401T

Бренды по названию

Популярные бренды

Kohler CURTIS 3401T, Руководство пользователя

Результаты поиска

Содержание CURTIS 3401T

Отзывы:

Похожие инструкции для CURTIS 3401T

Бренды по названию

Популярные бренды