manualshive.com logo in svg

Kohler CURTIS 3401T, Руководство пользователя

Поделиться
Скачать
Kohler CURTIS 3401T Скачать руководство пользователя страница 19

 2 — USING THE 3401T

pg. 13

Return to TOC

 

Curtis Model 3401T – August 2022

5.  Press the 

 button to submit the password. If the password is correct, the 3401T will list the 

Curtis devices on the CANbus.
If the password screen indicates that the wrong password was entered, press the 

 or 

  

button to clear the password, then repeat steps 3–5.

6.  If multiple devices are listed, use the 

 and   buttons to select the device you want to work 

with.

7.  Press the 

 button. The 3401T downloads the device’s menu and then displays the main menu. 

You can now 

view and edit parameters

.

To exit the menu, press the 

 button.

IMPORTANT: After you have finished working with parameters, cycle the keyswitch to clear 

the password.

Open Parameter Menus of Devices Connected to the Serial Port

The 3401T provides read-only access to the main and Monitor menus of Curtis devices that support 

the ESP/SP protocol and are connected through the serial port. Take the following steps to open 

these menus:

1.  Go to the home screen.
2.  Press the 

 button. The main menu displays and you can now view parameters.

To exit the menus, press the 

 button.

Содержание CURTIS 3401T































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды