Kohler CURTIS 3401T Скачать руководство пользователя страница 38

Страница: 38 / 62

4 — PROGRAMMABLE PARAMETERS

Curtis Model 3401T – August 2022

Return to TOC

pg. 32

SET HOURMETERS MENU

Use the Set Hourmeters menu to specify the password for resetting hour meters. After the password

has been entered the

Set Hourmeters submenu

is displayed. The submenu contains parameters that

reset the hour meters.
Note: The default password for resetting hour meters is 12345. Curtis recommends that you change

the default password.
Take the following steps to specify the password:

1. Specify the password as the Input Hrm Password parameter value.
2. Set the Confirm Input Password parameter to On. If the password is valid, the Set Hourmeters

submenu is displayed.

SET HOURMETERS MENU

PARAMETER

CAN INDEX

VALUES

RAW VALUES

DATA SIZE

ACCESS LEVEL

DEFAULT VALUE

DESCRIPTION

Input Hrm Password

0x6906:00

11111–99999

32-bit

OEM Dealer

55555

Specifies the password for resetting hour meters.

Note

: The default value is not the same value as the

actual password.

Confirm Input Password

0x6908:00

Off/On

0–1

32-bit

OEM Dealer

Off

Submits the password specified with the Input Hrm

Password parameter.

Status of Set Hourmeters

0x6907:00

Enumerated

0–1

32-bit

OEM Dealer

Disable

Indicates whether the hour meters can be reset:

0 = Disable
1 = Enable

When a valid hour meter password has been

specified, the value changes to Enable.
RO

Set Hourmeters Submenu

Use the Set Hourmeters submenu to reset hour meters and change the password for resetting them.

SET HOURMETERS SUBMENU

PARAMETER

CAN INDEX

VALUES

RAW VALUES

DATA SIZE

ACCESS LEVEL

DEFAULT VALUE

DESCRIPTION

Reset KSI Hourmeter

0x646A:00

Off/On

0–1

16-bit

OEM Dealer

Off

Resets the keyswitch hour meter.

Reset TRA Hourmeter

0x646B:00

Off/On

0–1

16-bit

OEM Dealer

Off

Resets the traction controller hour meter.

Reset HYD Hourmeter

0x646C:00

Off/On

0–1

16-bit

OEM Dealer

Off

Resets the pump controller hour meter.

Set KSI Hourmeter

0x642C:00

0–99999.9 hours

0–999999

32-bit

OEM Dealer

Sets the time indicated by the keyswitch hour meter.

Change Hrm Password

0x6905:00

11111–99999

32-bit

OEM Dealer

12345

The password for resetting the hour meters.

Содержание CURTIS 3401T































































Результаты поиска

Содержание CURTIS 3401T

Отзывы:

Похожие инструкции для CURTIS 3401T

Бренды по названию

Популярные бренды

Kohler CURTIS 3401T, Руководство пользователя

Результаты поиска

Содержание CURTIS 3401T

Отзывы:

Похожие инструкции для CURTIS 3401T

Бренды по названию

Популярные бренды