Kohler CURTIS 3401T Скачать руководство пользователя страница 46

Страница: 46 / 62

4 — PROGRAMMABLE PARAMETERS

Curtis Model 3401T – August 2022

Return to TOC

pg. 40

OUTPUT MENU

The Output Mode parameter specifies how pin 8 (Switch Input5/MOSFET OUTPUT) is used. The

Driver Output Setting parameter and the parameters on the following submenus apply when the

pin is used as a driver:

•  Ramp
•  Initial
•  Current Limit
•  Dither
•  PI

OUTPUT MENU

PARAMETER

CAN INDEX

VALUES

RAW VALUES

DATA SIZE

ACCESS LEVEL

DEFAULT VALUE

DESCRIPTION

Output Mode

0x6620:00

Enumerated

0–5

16-bit

OEM Dealer

Specifies the function for pin 8:

0 = Turn Off
1 = PWM Mode
2 = Voltage Mode
3 = Current Mode
4 = Lift Lock Mode
5 = Switch Input Mode

Driver Output Setting

0x66F0:00

0.0–100.0%

0–1000

16-bit

OEM Dealer

0.0%

Specifies the output when pin 8 is used as a driver.

How the parameter is used depends upon the

Output Mode:

• PWM mode: The actual duty cycle.
• Voltage mode: The product of this value and

the

Nominal Voltage

parameter is the actual

output voltage.

• Current mode: The product of this value and

the

Maximum Current

parameter is the actual

output current.

Ramp Menu

The following table describes the parameters on the Ramp menu.

RAMP MENU

PARAMETER

CAN INDEX

VALUES

RAW VALUES

DATA SIZE

ACCESS LEVEL

DEFAULT VALUE

DESCRIPTION

Ramp Up Time

0x6650:00

0–10000ms

0–10000

16-bit

OEM Dealer

8ms

Specifies the time it takes to go from minimum to

maximum output current.

Ramp Down Time

0x6660:00

0–10000ms

0–10000

16-bit

OEM Dealer

8ms

Specifies the time it takes to go from maximum to

minimum output current.

Содержание CURTIS 3401T































































Результаты поиска

Содержание CURTIS 3401T

Отзывы:

Бренды по названию

Популярные бренды

Kohler CURTIS 3401T, Руководство пользователя

Результаты поиска

Содержание CURTIS 3401T

Отзывы:

Бренды по названию

Популярные бренды