manualshive.com logo in svg

Kohler COM7.5, Руководство по обслуживанию

Поделиться
Скачать
Kohler COM7.5 Скачать руководство пользователя страница 40

TP-6120 5/02

30

Section 4 Component Testing and Adjustment

4.6.2

Rotor

The rotor uses permanent magnets. There are no tests
or field adjustments for the rotor.

4.7 Fault Shutdown Switches

Check the continuity of the high oil temperature (HOT)
and low oil pressure (LOP) switches. Check for loose
connections and open or short circuits in the connecting
wires before replacing the switches.

High Oil Temperature (HOT) Switch

The HOT switch is normally open. Shut down the
generator set and allow the engine to cool. Use an
ohmmeter to measure the resistance from pin P1-18 of
the engine harness (lead 37) to ground. The ohmmeter
should indicate an open circuit.

Any other reading

indicates a short; replace the HOT switch.

photos7--1

1. High oil temperature switch

1

Figure 4-12

High Oil Temperature (HOT) Switch

Low Oil Pressure (LOP) Switch

The normally closed LOP switch opens when the engine
oil pressure reaches the normal operating level and
closes if the oil pressure drops below a preset minimum.
Use an ohmmeter to check the continuity between pin
P1-17 of the engine harness (lead 13) and ground.
Verify that the switch is closed while the engine is
stopped. Start the generator set and check that the
switch opens approximately 5 seconds later.

If the

switch does not open after the engine reaches normal
operating speed, check the oil level and test for leaks in
the lubrication system before replacing the LOP switch.

photos3--9

1. Low oil pressure switch

1

Figure 4-13

Low Oil Pressure (LOP)Switch

Содержание COM7.5

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды