Kohler COM7.5 Скачать руководство пользователя страница 26

Страница: 26 / 64

TP-6120 5/02

Section 3 General Troubleshooting

3.2 Generator Set/Controller System Troubleshooting Flowcharts

Does

engine
crank?

Does

engine

start?

Yes

Did a fault

shutdown

occur?

Is the battery

connected?

Yes

Correct fault, reset

controller, and

continue

troubleshooting from

top of page.

Yes

Charge or replace the
battery and attempt to
restart. If engine does

not crank, continue

troubleshooting

sequence.

Check the battery

voltage. Is battery

fully charged?

Repair/replace starter.

See the Engine Service

Manual.

Yes

Check wiring

harnesses and

connections.

Reconnect, repair, or

replace wiring if

loose or damaged.

Move master switch

to RUN position.

Does engine start

and run normally?

Yes

Unit is okay.

Go to

Check starter wiring, relay, and

motor. Check voltage to starter

relay on lead 71. See Section

4.3. Is the starter okay?

Replace

controller

board.

Yes

Does unit stop

while master

switch is still in

AUTO?

Yes

Generator set is okay. The system
may have been sent a remote stop

command, or there may be a problem

with the system controller. Refer to

the system controller manufacturer’s

service information.

Unplug controller interface

connector to disconnect

remote control system.

Move master switch to

RUN position.

Move master switch
to the OFF position.

Connect the

battery.

Go to

Move master switch to STOP

position to reset controller faults.

Check for a blown

controller fuse. See

Section 5.1. Is the

fuse good?

Yes

Replace the fuse.
See Maintenance

and Service Parts.

Содержание COM7.5

































































Результаты поиска

Содержание COM7.5

Отзывы:

Бренды по названию

Популярные бренды

Kohler COM7.5, Руководство по обслуживанию

Результаты поиска

Содержание COM7.5

Отзывы:

Бренды по названию

Популярные бренды