Kohler COM7.5 Скачать руководство пользователя страница 35

Страница: 35 / 64

TP-6120 5/02

Section 4 Component Testing and Adjustment

The fuel shutoff solenoid deenergizes and the generator
set shuts down with the following electronic governor
faults:

Loss of pickup while running (throttle moves to closed

position)

Engine overspeed

Broken fuel shutoff solenoid lead

Loss of DC power to governor assembly

Broken stepper motor leads (erratic performance)

Actuator linkage failure (erratic performance)

If none of the above conditions exist, proceed to
Section 4.2.2, Stepper Motor Check.

photos2-7

1. Stepper motor
2. Throttle linkage

TP5867

Figure 4-3

Governor

4.2.2

Stepper Motor Check

Use the following procedure to test the operation of the
governor stepper motor.

Stepper Motor Test Procedure

1. Stop the generator set and disconnect the battery.

2. Manually

move

the

governor

linkage

fully

counterclockwise (open throttle). See Figure 4-3.

3. Reconnect the battery. The stepper motor should

move clockwise to the closed-throttle position with
a noticeable clicking sound. If the stepper motor
does not stay in the closed-throttle position,
replace the stepper motor.

Only two stepper motor leads of each coil group are
utilized (BLACK-YELLOW and RED-WHITE).

The

resistance per phase is 38.5 ohms. See Figure 4-4.

BLK

YEL

GRN

RED WHT

BLU

SB555

Figure 4-4

Actuator Coil Group

Содержание COM7.5

































































Результаты поиска

Содержание COM7.5

Отзывы:

Бренды по названию

Популярные бренды

Kohler COM7.5, Руководство по обслуживанию

Результаты поиска

Содержание COM7.5

Отзывы:

Бренды по названию

Популярные бренды