manualshive.com logo in svg

Kohler COM7.5, Руководство по обслуживанию

Поделиться
Скачать
Kohler COM7.5 Скачать руководство пользователя страница 18

TP-6120 5/02

8

Section 2 Scheduled Maintenance

2.3.4

Oil Cooler

Use compressed air or a brush to clean the oil cooler fins
after every 100 hours of operation (or more frequently if
the generator set operates under dusty or dirty
conditions). See Figure 2-2 for the oil cooler location.

2.3.5

Low Oil Pressure Shutdown

The low oil pressure shutdown feature protects the
engine against internal damage if the oil pressure drops
below a safe operating value because of oil pump failure
or other malfunction. This shutdown feature does not
protect against damage caused by operating with the oil
level below the safe range—it is not a low oil level
shutdown. Check the oil level regularly and add oil as
needed.

2.4 Air Cleaner Element and

Precleaner

The engine has a replaceable high-density paper air
cleaner element with an oiled-foam precleaner. See
Figure 2-3. Refer to the service views in Section 1.4 for
the air cleaner’s location.

Follow the enclosure

manufacturer’s instructions to open the enclosure and
gain access to the air cleaner.

Wash and oil the precleaner and replace the paper
element at the intervals shown in the service schedule.
Service the air cleaner more often if the generator set
operates under dusty or dirty conditions.

Refer to

Maintenance and Service Parts in the Introduction
section of this manual for replacement part numbers.

Keep the area around the air cleaner housing free of dirt
and debris.

Note:

Operating the engine with loose or damaged air
cleaner components could allow unfiltered air
into the engine, causing premature wear and
failure.

Fire.
Can cause severe injury or death.

Do not smoke or permit flames or
sparks near fuels or the fuel system.

WARNING

Servicing the air cleaner. A sudden backfire can cause
severe injury or death.

Do not operate the generator set with

the air cleaner removed.

1

2

3

4

5

6

7

586536

1. Cover knob
2. Air cleaner cover
3. Element cover nut
4. Element cover
5. Foam precleaner
6. Air cleaner element
7. Air cleaner base

Figure 2-3

Air Cleaner Components

Содержание COM7.5

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды